Phani Gubbala's Communities Activities

Annotation Groups ORD

Kristina Ward — Thu, 17 Jun 2021 16:02:46 GMT

I'm having issues with cross section labeling using the XS Annotation Group. It seems as though only certain slope %s get picked up to be labeled. Is there a simple way to add these slope labels to the annotation group library? Or even to manually label the XS.

Appreciate any help.

Curb Ramp Ovals

Barry Hurst — Mon, 19 Jul 2021 12:54:34 GMT

I am looking to start placing the annotation for the CCR Ramps and can't find a good way to place the annotation. The CADD Manual shows a cell but it isn't in the current cell library. Any ideas on the best way to place this?

Printing sheets in ORD

Phani Gubbala — Fri, 03 Sep 2021 12:48:01 GMT

When I print out the sheets in hardcopy the scale is off.

How can I fix this issue?

Printing Cross Sections in ORD

Kristina Ward — Fri, 27 Aug 2021 12:01:01 GMT

Has anyone had issues with printing cross sections? We have a pretty large model on this project so I'm sure that slows it down but I haven't had this issue in the past. It seems to be getting stuck here:

Any help would be appreciated!

Ask A Question II

Tue, 15 Jun 2021 18:51:15 GMT

Ask 10 questions in a forum.

Scale in Template Library

Phani Gubbala — Thu, 26 Sep 2019 12:50:50 GMT

So I created multiple templates for a project. All of them were zoomed in Y direction by default. One time I was switching between templates and on of the templates lost it's zoom in Y direction. I tried to do it manually and save it but it comes back to 1 to 1. Is there a way I could zoom it in Y direction and save settings so that it does not switch to 1 to 1 scale again?

Right side slope tie in jumps to the left even after increasing the priority of the left side slope component.

Phani Gubbala — Fri, 14 Jun 2019 13:32:33 GMT

Hello,

I am having this issue with my slope tie ins. I am using the FDOT end conditions. Cut & Fill to R/W on the right and Cut & Fill on the left. I first added the Cut & Fill to R/W end condition on the right and it is working as it is supposed to. As soon as I added the Cut & Fill end condition on the left the 1:4 slope tie in, projected to active surface (which comes after the 1:6 slope, until the clear zone) is jumping to the left as shown in the picture. I thought it could be resolved by giving the same priority for both tie in components on either side and it did not work. Then I tired increasing the priority of tie ins on the left side and it still did not work. I am not really sure what the exact problem is. Could anyone please help me with this.

Thank you for you time in advance.

offsetting a curve makes it a b-spline

Phani Gubbala — Tue, 20 Feb 2018 18:21:14 GMT

Hello,

I am trying to offset a curve using the move parallel tool and it is giving me a B-Spline curve. How can I correct this issue?

Thanks in advance.

Phani

can't resize the ancillary feature dialogue box after minimizing

Phani Gubbala — Tue, 06 Feb 2018 20:57:32 GMT

As the subject describes, I am having difficulty restoring my Draw Ancillary Feature tool to its original size. I have used the following links to address the issue:

http://communities.bentley.com/products/road___site_design/w/road_and_site_design__wiki/12912.geopak-ancillary-features

http://communities.bentley.com/products/road___site_design/f/5922/t/35845

http://communities.bentley.com/communities/user_communities/fdot_cadd_support/f/343103/t/84164

I'd appreciate any input you all have...Thanks,

Problem with dimensions

Phani Gubbala — Fri, 15 Dec 2017 14:28:49 GMT

I am trying to place dimensions. When I measure the line it shows up as 12' but when I try to plave the dimension it shows up as 9.26'. Do you know hat might be causing this problem?

ancillary features. (not working for some XS)

Phani Gubbala — Thu, 14 Dec 2017 16:55:01 GMT

Hello,

I am trying to draw lines using ancillary features and I do not understand why but the tool is not drawing the lines in some of the cross sections. I also tried this by copying the lines into the XS file but it still does the same thing. I do not understand why this is happening. Could any one please help.

Thanks.

Not able to create xs from the model using civil tools "create xs"

Phani Gubbala — Mon, 04 Dec 2017 15:15:49 GMT

I am trying to create XS from the model and I am using the create XS tools in the Civil Cell Tool bar. I chose 1:20 scale gave the model a unique name, went into custom tab and selected all my pattern lines and chose line string and hit graphics which loaded all my pattern lines. Then when I click apply it just loads super fast but do not create a model or XSs. Can you please tell me what might be the problem here?

Thank You.

Ask A Question I

Mon, 13 Nov 2017 00:56:17 GMT

Ask a question in a forum.

what is a .gen file and how can I create a .gen for cross sections?

Phani Gubbala — Mon, 26 Jun 2017 12:56:06 GMT

I am trying to understand what a .gen file is and how can I create one? Please help!

one cross-section is missing from the cross section navigator.

Phani Gubbala — Wed, 21 Jun 2017 18:24:19 GMT

hello.

I open the cross section navigator and one of the cross sections is not showing up in the navigator. I do not understand what the problem is. Is there a way I can bring that cross section back to show up in the cross section navigator?