Bentley Communities
Bentley Communities
  • Site
  • User
  • Site
  • Search
  • User
LARS | LEAP | OpenBridge | OpenTunnel | RM
  • Product Communities
LARS | LEAP | OpenBridge | OpenTunnel | RM
LARS | LEAP | OpenBridge | OpenTunnel | RM Wiki How to add a void to Slab Bridge
    • Sign In
    • LARS | LEAP | OpenBridge | OpenTunnel | RM
    • OpenBridge Designer: Onboarding Guide
    • How to Download OpenBridge Modeler or OpenBridge Designer?
    • +Bridge Products: Operating System and Hardware Requirements
    • +OpenBridge Modeler CONNECT Edition
    • +OpenBridge Designer CONNECT Edition
    • -LEAP Bridge Concrete - CONSPAN, CONBOX, RC-PIER, CONSPLICE, and GEOMATH inside OpenBridge Designer CONNECT Edition
      • +LEAP Bridge Concrete main interface
      • -LEAP CIP RC/PT Girder - CONBOX
        • Axial Forces -- Dead Load case
        • CIP RC/PT Girder Analysis Type
        • Column Design in Conbox
        • Custom Live Load in Leap Conbox
        • Customization of Section in Conbox
        • De-Couple Tendon Forces between Spans
        • Definition of Super-element
        • Design output - what is Moment (SC) ?
        • Design Results for V/M Interaction
        • Different types of Losses
        • How do I model a Tee beam cast in place bridge?
        • How do I print rating results under CIP Bridge module
        • How to add a void to Slab Bridge
        • How to remove a portions of slab in Slab Bridge
        • Influence Lines Diagram
        • Input of Live Load Distribution Factors Manually
        • Live Load Distribution Factor -- Range of Applicability of Table 4.6.2.2.2b-1
        • Live Load Forces and Moment Calculation- Service I Limit State
        • Live Load Reaction Calculation
        • Long Term Deflection
        • Manual Input of Allowable Stress and other relevant information.
        • Modeling Varying Width of Box Girder
        • Points of Interest
        • Points of Interest --"FSupp1Ld" and "FSupp1Rd"
        • Positive Moment Capacity Calculation -- Top & Bottom Rebar
        • Post Tension I girder -- AASHTO LRFD Code
        • Post Tensioned Box Girder: Initial and Final Dead Load Deflection.
        • +Printing the Output in an Enhanced format
        • Rebar and Stirrups Design -- The Design Icon gets greyed out
        • Reduce web width Bv, for Presence of Duct.
        • Reduction of Analysis Time.
        • Relation between Diaphragm and P-Jack Force.
        • Running the Analysis - Design Icon gets greyed out.
        • Sign-conventions in Conbox
        • Skew Correction Factor option
        • Skewed Bridge - Distribution of Load from Superstructure to Substructure.
        • Skewed Slab Bridge - Skew Correction factor.
        • Slab Bridge - Exterior Strip width Design
        • T beam -- Modeling Different Beam width for Exterior and Interior Girders
        • T- Beam Bridge - Type of Analysis
        • Truck and Live Loads have named cases with and without “Displacement” .
        • Where are design code options located under Cast in Place (CIP) module?
        • will the live load (LL) run in between barriers positioned on the CIP box?
      • +LEAP CONSPAN / Precast/Prestressed Girder
      • +LEAP RCPIER - Substructure
      • Enhancements and corrections in LEAP Bridge Concrete version 22.00.02.19 (part of Open Bridge Designer version 10.11.00.40 (September 2022)
      • How do I find out the AASHTO Code option I am using?
      • SELECTsupport TechNotes And FAQs
      • Service Design Check- LFD & ASD
      • Where is the consolidated library of LEAP Bridge Concrete located?
      • Working Remotely with LEAP Applications
    • +LEAP Bridge Steel - OpenBridge Designer
    • +RM Bridge - OpenBridge Designer
    • +LARSBridge V20
    • +OpenTunnel Designer CONNECT Edition
    • +How to log Case?
    • USA State DOT links
    • OpenBridge - OpenTunnel Ideas
    • Working from Home with OpenBridge Modeler
    • Working Remotely with OpenBridge Designer
    • OpenBridge Tips and Tricks

     
     Questions about this article, topic, or product? Click here. 

    How to add a void to Slab Bridge

      

    Document Information

    Document Type: FAQ

    Product(s): LEAP CONBOX/CIP RC/PT Girder

    Version(s): All

    Original Author: Bentley Leap Bridge Technical Support Group – VM

    QUESTION: How to add a void at the center of the cross section of slab bridge?

    ANSWER:

    This is just an example to show how voids are added in a slab bridge.

    Go to Geometry TAB and then click on Cross Section button. In the New Cross section Layout window click on SECTION option under Section Definition heading.

    In the new Multi-cell CIP Box Section  window click on PARTS button.

    In the new Multi-cell CIP Box Parts window please select CIRCLE under TYPE and HOLE option under STATUS heading.

    Then finally input these below mentioned values to create a 1ft dia. VOID at the center of the slab bridge cross section.

    Ref-Z(ft)  = 0.00

    Ref-Y(ft)  = 1.25

    H(ft)         = 0.5

    V(ft)         = 0.5

    Please see the attached screenshots for more information.

    • Add a void to Slab Bridge
    • CIP RC/PT Girder
    • Share
    • History
    • More
    • Cancel
    • Vinay mysore Created by Bentley Colleague Vinay mysore
    • When: Thu, Aug 20 2015 7:15 AM
    • Dilip Matange [Bentley] Last revision by Bentley Colleague Dilip Matange [Bentley]
    • When: Wed, Feb 24 2021 4:44 PM
    • Revisions: 6
    • Comments: 0
    Recommended
    Related
    Communities
    • Home
    • Getting Started
    • Community Central
    • Products
    • Support
    • Secure File Upload
    • Feedback
    Support and Services
    • Home
    • Product Support
    • Downloads
    • Subscription Services Portal
    Training and Learning
    • Home
    • About Bentley Institute
    • My Learning History
    • Reference Books
    Social Media
    •    LinkedIn
    •    Facebook
    •    Twitter
    •    YouTube
    •    RSS Feed
    •    Email

    © 2023 Bentley Systems, Incorporated  |  Contact Us  |  Privacy |  Terms of Use  |  Cookies