HELP WITH LOAD CALCULATIONS DATA AND TRANSFERRING IT INTO TOTAL BUILDING DESIGN

RE: HELP WITH LOAD CALCULATIONS DATA AND TRANSFERRING IT INTO TOTAL BUILDING DESIGN

seamus murphy — Wed, 15 Apr 2020 13:38:39 GMT

Hi Shane

Good to hear.

That's Great Ill bash away at that now and try to get them link together.

Thanks again for your speedy reply , I greatly appreciate it.

Kind Regards

Seamus Murphy

RE: HELP WITH LOAD CALCULATIONS DATA AND TRANSFERRING IT INTO TOTAL BUILDING DESIGN

Shane Regan — Wed, 15 Apr 2020 13:33:55 GMT

Hi Seamus,

I'm doing well all things considered, many thanks, hope you are too. It's usually a case of drawing vertical risers up to the height of the floor above, and then entering the correct values into the Floor Change Connector menu. I'm not sure if you have seen our step by step guide on this? This can be found here.

So, for floor -1, you would rise from 2.8m to 3m, then place the connector. If you need any more specific instructions by all means let me know.

RE: HELP WITH LOAD CALCULATIONS DATA AND TRANSFERRING IT INTO TOTAL BUILDING DESIGN

seamus murphy — Wed, 15 Apr 2020 13:21:32 GMT

Good afternoon Shane

I hope you are keeping well during this difficult time.

I am wondering if I maybe able to get your assistance.

I am having great difficulty in adding in floor connectors for my cold water services installation using Netsys.

Each floor is 3m in height with the pipe work on each floor level @ 2.8m , bar the roof level where it is @ 0.45 m off ground

Can you please provide some assistance on how to install the floor connectors to connect the rising main to each floor ???

Any help on this matter is greatly appreciated .

I can also send on the netsys pipe files if needed.

NETSYS CWS INFORMATION

floor -1 - plant cws system marker located on this floor

FFL IS @ 0M

cws pipe work level 2.8m

Floor 0

FFL IS @ 3M

cws pipe work @ 2.8m

Floor 1

FFL IS @ 6M

cws pipe work at 2.8m

Floor 2 - GREEN ROOF.

FFL IS @ 9M

cws feeding 3 roof taps @ 0.45m

Kind Regards

Seamus Murphy

Junior Mechanical Engineer

Homan O'Brien • Consulting Engineers

89 Booterstown Avenue Blackrock, Co. Dublin, A94 P2C2, Ireland.

Tel: +353 (01) 2056300 Fax: +353 (01) 2056301

Email: seamus.muprhy@homanobrien.ie Web: www.homanobrien.ie

P please consider the Environment before printing this E-Mail

This E-mail and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed.
Any views or opinions presented are solely those of the author, and do not necessarily represent those of Homan O'Brien. If you have received this email in error please notify the sender.
Although Homan O'Brien scans E-mail and attachments for viruses, it does not guarantee that either is virus-free and accepts no liability for any damage sustained as a result of viruses.

Homan O’Brien & Co. Limited trading as Homan O’Brien Associates. Directors: Brian Homan, Simon O’Brien, Gerard Keating, James Reilly. Registered in Ireland No: 158319. Registered Office: 89 Booterstown Ave, Blackrock, Co. Dublin.

RE: HELP WITH LOAD CALCULATIONS DATA AND TRANSFERRING IT INTO TOTAL BUILDING DESIGN

Shane Regan — Fri, 23 Aug 2019 15:43:27 GMT

No problem at all Shay, if you need anything else just get in touch.

RE: HELP WITH LOAD CALCULATIONS DATA AND TRANSFERRING IT INTO TOTAL BUILDING DESIGN

seamus murphy — Fri, 23 Aug 2019 15:39:28 GMT

HI Shane

Thanks for your reply.

That's good advice cheers. I will continue going the way I was originally going using the design Data Base as well as the Netsys pipe and duct sizing tools.

Best Regards

Shay

RE: HELP WITH LOAD CALCULATIONS DATA AND TRANSFERRING IT INTO TOTAL BUILDING DESIGN

Shane Regan — Fri, 23 Aug 2019 15:36:07 GMT

Hi Seamus,

There is no way of doing so unfortunately, the programs use quite different formats so they are not interchangeable. Generally I would advise using Design Database and Netsys, as System Builder has not been updated for quite some time.