Bentley Communities
Bentley Communities
  • Site
  • User
  • Site
  • Search
  • User
Hevacomp
  • Product Communities
  • Building
  • Hevacomp
  • Cancel
Hevacomp
Hevacomp Wiki Pipe sizing - heating and cooling methods
    • Sign In
    • +Hevacomp General Information
    • +Hevacomp Dynamic Simulation
    • +Hevacomp Electrical Designer
    • -Hevacomp Mechanical Designer
      • +Design Database - Hevacomp Mechanical Designer
      • +Mechanical Design - Hevacomp Mechanical Designer
      • -Netsys - Hevacomp Mechanical Designer
        • Can a project be used as a basis for a different project type?
        • Can I get any sample Netsys projects?
        • Changing the DXF background
        • Changing the snap grid
        • Connecting emitters to a reverse return system
        • Converting Flow Rates from Loading Units To Litres Per Second
        • Defining pipe headers
        • Duct sizing - allowing for a depression
        • Duct Sizing - Drawing an offset to avoid duct clashes.
        • Duct Sizing - Excessive Ductwork pressure due to Universal tees
        • Duct Sizing - Fitting, terminator and connection codes
        • Duct Sizing - How to connect a diffuser to the underside of a plenum box
        • Duct Sizing - Pressure drop considerations on outlets
        • Duct sizing - resetting the outlet references
        • Duct sizing - Roughness figures
        • Gas pipe sizing - Bouyancy and Residual Pressures
        • Gas pipe sizing - Changing surrounding temperature doesn't affect results
        • Gas Pipe Sizing - Diversity not included
        • Gas pipe sizing - Source pressure is considered when calculating Velocity
        • Heating and Chilled water - Excessive pressure drop
        • Heating and Chilled water - Higher than expected flow rates
        • How to add Floor Change Connectors
        • How to display Section Numbers on your Netsys system
        • How to fix a vertical pipe or duct
        • How to model angled riser with Floor Change Connector
        • Including Hot Water System feed in your Cold Water System
        • Inconsistent Flow Rate at Outlets
        • Netsys annotation - adding pipe or duct notes
        • Netsys annotation - displaying unusual results
        • Netsys annotation - Pipe properties tree
        • Netsys annotation - refreshing pipe or duct notes
        • Netsys warning - Closed loop found in system
        • Netsys warning - Insufficient Pressure
        • Netsys warning - No flow in pipe
        • Netsys warning - Spurious connection or 0mm Pipe size
        • Pipe and Duct fittings - K values
        • Pipe sizing - heating and cooling methods
        • Pipe sizing - how to add a CWS tank
        • Pipe sizing - Outlet resistance is considered in circulating pump sizing
        • Pipe sizing - Pipe diameters and insulation thickness
        • Pipe Sizing - Pipe lengths in reports
        • Pipe sizing - Pipe Sizing Standards
        • Pipe Sizing - Roughness figures and equivalent range selection
        • Pipe sizing - Special outlets cause excessive pipe sizes
        • Pipe sizing - Water content for heating and cooling emitters
        • Why can't the pipe or duct height be changed?
      • +PartL - Hevacomp Mechanical Designer
      • +System Builder - Hevacomp Mechanical Design
    • +Installation and activation
    • +Troubleshooting
    • +Windows tips and tricks
    • Working From Home with Hevacomp

     
     Questions about this article, topic, or product? Click here. 

    Pipe sizing - heating and cooling methods

      Product(s): Hevacomp Mechanical Designer
      Version(s): V8i
      Environment: N/A
      Area: Netsys
      Subarea: Results

    Overview

    While using Netsys Heating or Chilled water it may be noted that the pressure drop for pipe sections exceeds the maximum pressure drop provided through the system marker.

    Method

    The software follows these methods during sizing:

    1. Initial sizing of pipe work based upon the required flow rate
       
    2. Limiting velocities are considered and pipe sizes are increased using an iterative process if required. This can overrule the initial sizing.
       
    3. Limiting pressure drops constraints are now checked against calculated pipe pressure drops, excluding fittings; Pipe sizes are increased using an iterative process if required.

      This method considers limiting pressures drop for pipe sections only. Fitting pressure drops are not considered during steps 1, 2 and 3.
       
    4. Once pipes are sized, the pressure drops for bends, tees and other fittings can be calculated. The pressure drops are then added to the pipe pressure drop to provide the Total pressure drop. The pressure drop/M is calculated from Total Pressure Drop/Pipe Length. This final figure is displayed on the results pages.

    • heat heating
    • Mechanical
    • V8i V26
    • chill chiller
    • Hevacomp
    • netsys
    • Building Performance
    • Share
    • History
    • More
    • Cancel
    • Duncan Brown Created by Duncan Brown
    • When: Wed, Aug 27 2014 5:25 AM
    • Duncan Brown Last revision by Duncan Brown
    • When: Thu, Jan 18 2018 6:07 AM
    • Revisions: 8
    • Comments: 2
    Recommended
    Related
    Communities
    • Home
    • Getting Started
    • Community Central
    • Products
    • Support
    • Secure File Upload
    • Feedback
    Support and Services
    • Home
    • Product Support
    • Downloads
    • Subscription Services Portal
    Training and Learning
    • Home
    • About Bentley Institute
    • My Learning History
    • Reference Books
    Social Media
    •    LinkedIn
    •    Facebook
    •    Twitter
    •    YouTube
    •    RSS Feed
    •    Email

    © 2023 Bentley Systems, Incorporated  |  Contact Us  |  Privacy |  Terms of Use  |  Cookies