Get the ID rather than the phase number when scripting

RE: Get the ID rather than the phase number when scripting

Grissel Hurtado — Fri, 12 Feb 2021 15:56:16 GMT

Thank you very much for the prompt response, some of these articles I had already reviewed, what I could not find was the explanation you gave me about the load when you use an asterisk.

thank you

De: Stefanos Papavasileiou [bounce-cdbba617-aa83-4c94-b37e-bf6969746ae6@communities.bentley.com]
Enviado: viernes, 12 de febrero de 2021 05:15 a.m.
Para: PLAXISSOILVISION@communities.bentley.com
Asunto: RE: [PLAXIS | SOILVISION Forum] Get the ID rather than the phase number when scripting

Update from Bentley Communities

Stefanos Papavasileiou

Dear Grissel,

Following my answer to the service request earlier this week I include my response here for the Forum.

Unfortunately, we do not have such a specific Python script, however, I believe that with the information below you can succeed.

First of all, please check the Wiki article about the Python scripting in understanding how to work with our boilerplate: communities.bentley.com/.../using-plaxis-remote-scripting-with-the-python-wrapper

I would also strongly advise you to check our Scripting reference as we give examples for every command used in PLAXIS: communities.bentley.com/.../scripting-reference-and-how-to-use-it

The following article is very useful in understanding the command syntax in PLAXIS and what is needed by Python:
communities.bentley.com/.../identify-python-commands-from-plaxis-command-line

Then, we have quite a few examples on our Wiki pages of various cases that you can use: communities.bentley.com/.../api-python-scripting---plaxis

To give you a quick answer, adding a load in Structure mode can be done with the following command:

PLAXIS: lineload (0 0) (2 0)
Python: g_i.lineload(0, 0, 2, 0)

PLAXIS: set Line_1.LineLoad.qy_start -100
Python: g_i.Line_1.LineLoad.qy_start = -100
or g_i.LineLoad_1.qy_start = -100
or g_i.LineLoad_1.qy_start.set(-100)

In Staged construction you can activate and change the value like this:

PLAXIS: activate (LineLoad_1_1) Phase_1
Python: g_i.activate(g_i.LineLoad_1_1, g_i.Phase_1)

PLAXIS: set LineLoad_1_1.qy_start Phase_1 -150
Python: g_i.LineLoad_1_1.qy_start[g_i.Phase_1] = -150
or g_i.LineLoad_1_1.qy_start.set(g_i.Phase_1, -150)

View online

You received this notification because you subscribed to the forum. To unsubscribe from only this thread, go here.

Flag this post as spam/abuse.

Puede consultar el Aviso de Privacidad del Instituto de Ingeniería UNAM en: http://www.iingen.unam.mx

RE: Get the ID rather than the phase number when scripting

Stefanos Papavasileiou — Fri, 12 Feb 2021 11:15:37 GMT

Dear Grissel,

Following my answer to the service request earlier this week I include my response here for the Forum.

Unfortunately, we do not have such a specific Python script, however, I believe that with the information below you can succeed.

I would also strongly advise you to check our Scripting reference as we give examples for every command used in PLAXIS: communities.bentley.com/.../scripting-reference-and-how-to-use-it

The following article is very useful in understanding the command syntax in PLAXIS and what is needed by Python:
communities.bentley.com/.../identify-python-commands-from-plaxis-command-line

Then, we have quite a few examples on our Wiki pages of various cases that you can use: communities.bentley.com/.../api-python-scripting---plaxis

To give you a quick answer, adding a load in Structure mode can be done with the following command:

PLAXIS: lineload (0 0) (2 0)
Python: g_i.lineload(0, 0, 2, 0)

PLAXIS: set Line_1.LineLoad.qy_start -100
Python: g_i.Line_1.LineLoad.qy_start = -100
or g_i.LineLoad_1.qy_start = -100
or g_i.LineLoad_1.qy_start.set(-100)

In Staged construction you can activate and change the value like this:

PLAXIS: activate (LineLoad_1_1) Phase_1
Python: g_i.activate(g_i.LineLoad_1_1, g_i.Phase_1)

PLAXIS: set LineLoad_1_1.qy_start Phase_1 -150
Python: g_i.LineLoad_1_1.qy_start[g_i.Phase_1] = -150
or g_i.LineLoad_1_1.qy_start.set(g_i.Phase_1, -150)

RE: Get the ID rather than the phase number when scripting

Grissel Hurtado — Mon, 08 Feb 2021 18:27:00 GMT

excuse some example where a load is applied is that when I run my script it marks an error in the module and I don't know why it should be

RE: Get the ID rather than the phase number when scripting

Rushan Gizzatullin — Fri, 15 Jan 2021 12:32:59 GMT

Dear Robin Rohwer Bokvist,

You can try to use:

g.Phases[1].Identification.value

More information you can find in the Command reference and in Scripting reference:

For example (Command reference → Input → Input objects reference → Phase):

In command line we can use:

_set Phase_1.Identification "Some phase title"