Bentley Communities
Site
Search
User
Site
Search
User
Welcome
Products
Support
About
More
Cancel
Product Communities
More
AutoPIPE
AutoPIPE Wiki
21. Model Wind Sway On A Pipe Rack in AutoPIPE
Sign in
-
Pipe and Vessel Stress Analysis - Wiki
+
ADL PIPE
-
Bentley AutoPIPE
++Table Of Contents - AutoPIPE Wiki page
+
- General Information about AutoPIPE
+
-NEW User Guide - TIPs - FAQ - RSS Newsfeed - AutoPIPE
+
ATS, ITS, and Batch Processing - AutoPIPE
AutoPIPE QA&R program
Bentley AutoPIPE Basic User Accrediation
+
Download - Install - Release Notes - AutoPIPE
+
File / Model Management using AutoPIPE
+
General - AutoPIPE
+
Graphics - AutoPIPE
+
Grids (Input & Results) - AutoPIPE
+
Import and Export - AutoPIPE
+
Known Issues in AutoPIPE (Enhancements, defects, etc..)
+
Libraries - AutoPIPE
+
License AutoPIPE -
-
Loads and Load Sets - AutoPIPE
01. Animate Load cases - AutoPIPE
02a. Load Case Descriptions in AutoPIPE
+
02b. Static Analysis in AutoPIPE
+
02c. Dynamic Analysis in AutoPIPE
+
02e. "Hydrotest" - AutoPIPE Load Case
+
02f. "Static Earthquake" - AutoPIPE Load Case
-
02g. "Wind" - AutoPIPE Load Case
05. How is the ground elevation determined for a Wind load case in an AutoPIPE model?
06. How to input a Wind profile using Wind Velocity instead of Wind Pressure in AutoPIPE?
07. How to account for East and West wind in both +ve and -ve directions in AutoPIPE?
08. Will "Inclined" wind direction set to off global axis take care of user required eccentric, torsional, or pitched loading of FPSO or off shore platforms in AutoPIPE?
09. Should the Wind Shape Factor Multiplier be 1 or 0.7 when using the ASCE wind specification type in AutoPIPE?
10. How to apply the same wind speed over the entire model in AutoPIPE?
11. How can the pipe movement be greater than the support gap setting for wind load combinations in AutoPIPE?
12. Is the pressure used in a wind profile the basic pressure (i.e. acting on a plate), or do I have to adjust the pressure for a pipe when inputting the figure in AutoPIPE?
13. What is the interpretation for annual probability and its relevance for determining wind load in AutoPIPE?
14. Is there any way to consider friction only the expansion case but not in any occasional AutoPIPE Wind loads?
15. Does AutoPIPE count pipe insulation thickness towards the effective diameter for wind/wave force calculations?
16. Where can one find information on ASCE 7 Wind speeds for AutoPIPE?
18. Why does the wind load appear that is not being applied to the model in AutoPIPE?
19. Why does the Wind direction Dx, Dy, Dz values change on the Wind Profile dialog in AutoPIPE?
20. Are ASCE7 - 2010 Wind loads ASD or LRFD in AutoPIPE
21. Model Wind Sway On A Pipe Rack in AutoPIPE
22. How to convert from wind loads from MPH to PSF in AutoPIPE?
23. What is the value of ASCE 7 Wind load setting "Cf" when value is set to Automatic in an AutoPIPE model?
24. Using ASCE 7 Is basic wind speed assumed to be sustained or a gust in an AutoPIPE model?
25. How are Wind loads applied to Constant Spring supports in AutoPIPE?
26. Is Kd term missing from ASCE 7-10, so Is this mix of 7-05 and 7-10 for AutoPIPE Wind load?
Nonlinear wind load analysis in AutoPIPE
+
02h. "Snow Load" - AutoPIPE Load Case
02i. "Thermal Bowing" - AutoPIPE Load Case
+
02k. "Response / Force Spectrum Loads" - AutoPIPE Load Case
+
02n. "Harmonic" - AutoPIPE Load case
02p. "Time History" (M1-M50) - AutoPIPE Load Case
02s. "Buoyancy" - AutoPIPE Load Case
+
02t. "Wave" - AutoPIPE Load Case
+
02u. "Fluid Transient" - AutoPIPE Load Case
02v. "Steam Relief" - AutoPIPE Load Case
+
02w. "Thermal Transient Analysis" (TTA) - AutoPIPE Load Case
+
03a. "Gravity" - AutoPIPE Load Case
+
03b. "Pressure" - AutoPIPE load case
03c. "Temperature" - AutoPIPE load case
+
03d. "SAM" (Seismic Anchor Analysis) - AutoPIPE load case
+
03e. "Fatigue" - AutoPIPE load case
+
03f. "Xtra Data" - AutoPIPE load case
+
03g. "Occasional" - AutoPIPE load case
04. Results From Loads and Load Sets Not Answered By Piping Code Calculations
+
05. Combination Load Cases (Tools> Combinations dialog)
+
06. Non-linear Load Sequencing Explained
+
Localization (Non-English Language) - AutoPIPE
+
Modeling Approaches in AutoPIPE
+
Modules (i.e. Flange Analysis, Spring Hanger Selection, Rotating Equip, TTA) in AutoPIPE
+
Piping codes - AutoPIPE
+
Post Processing - AutoPIPE
+
Printing - AutoPIPE
+
Reports - AutoPIPE
Security
+
Settings - AutoPIPE
+
Stress Isometrics - AutoPIPE
+
Technology Productivity Capabilities
+
Warnings, Errors, Crashed, Confirm, etc.. messages in AutoPIPE
+
~ Technical Support - AutoPIPE
+
Bentley AutoPIPE Nozzle (WinNOZL)
+
Bentley AutoPIPE Vessel (powered by Microprotol)
+
Bentley PlantFLOW
+
Bentley PULS
Multi-lingual announcement from BENTLEY TECHNICAL SUPPORT.
+
Training - Webinar - Help
Working at Home with AutoPIPE
+
~ Attend a live meeting with an AutoPIPE Analyst
21. Model Wind Sway On A Pipe Rack in AutoPIPE
Revision
Creation Date
Revision Author
Select All
Current Revision
Thu, Mar 9 2017 3:29 PM
Mike Dattilio
6
Revision #6
Mon, Oct 24 2016 12:41 PM
Mike Dattilio
5
Revision #5
Mon, Oct 24 2016 12:32 PM
Mike Dattilio
4
Revision #4
Fri, Jul 31 2015 12:23 PM
Mike Dattilio
3
Revision #3
Fri, Jul 31 2015 12:16 PM
Mike Dattilio
2
Revision #2
Fri, Jul 31 2015 12:16 PM
Mike Dattilio
1
Revision #1
Fri, Dec 12 2014 2:55 PM
Mike Dattilio
Compare Versions
View current version