Bentley Communities
Bentley Communities
  • Site
  • User
  • Site
  • Search
  • User
AutoPIPE
  • Product Communities
AutoPIPE
AutoPIPE Wiki 01. Why are my V-stops not allowing lateral movement during a Hydrotest load case in AutoPIPE ?
    • Sign In
    • -Pipe and Vessel Stress Analysis - Wiki
      • +ADL PIPE
      • -Bentley AutoPIPE
        • +- General Information about AutoPIPE
        • +- NEW User Guide for AutoPIPE
        • +- Technical Support - AutoPIPE
        • +Batch Processing, ITS, and ATS using AutoPIPE
        • AutoPIPE QA&R program
        • +Download - Install - Release Notes - AutoPIPE
        • +File / Model Management using AutoPIPE
        • +General - AutoPIPE
        • +Graphics - AutoPIPE
        • +Grids (Input & Results) - AutoPIPE
        • +Import and Export - AutoPIPE
        • +Known Issues in AutoPIPE (Enhancements, defects, etc..)
        • +Libraries - AutoPIPE
        • +License AutoPIPE -
        • -Loads and Load Sets - AutoPIPE
          • 01. Animate Load cases - AutoPIPE
          • 02a. Load Case Descriptions in AutoPIPE
          • +02b. Static Analysis in AutoPIPE
          • +02c. Dynamic Analysis in AutoPIPE
          • -02e. "Hydrotest" - AutoPIPE Load Case
            • 01. Why are my V-stops not allowing lateral movement during a Hydrotest load case in AutoPIPE ?
            • 02. Is there a method to perform a Hydrotest as a non-linear analysis in AutoPIPE?
            • 03. Where are the factors and values that are used in a Hydrotest load case located in AutoPIPE's output (report) file
            • 04. Why are my Hydrotest results so high in AutoPIPE?
            • 05. How to apply the Hydrotest load and analyze it in the new version of AutoPIPE V8i 09.06.01.10?
            • 06. Why does the Hydrotest case show an Allowable K Factor of 0.9 in AutoPIPE?
            • 07. How to assign code allowable stress for hydrotest loading: hoop stress and HY stress combination in AutoPIPE?
            • 08. How to calculate the Hydrotest Hoop stress and Allowable values in AutoPIPE?
            • 10. Why is there a difference in results between the Normal Sustain load (ex. Gr+MaxP (1)) and the Hydrotest Sustain load (ex. Gr+MaxP (2)) in AutoPIPE?
            • 11. How to apply more than one hydro-test analysis sets with different settings to an AutoPIPE model?
            • 14. Why is the gravity load case results weigh more than the Hydrotest gravity load case results on a Gas pipe line modeled in AutoPIPE?
          • +02f. "Static Earthquake" - AutoPIPE Load Case
          • +02g. "Wind" - AutoPIPE Load Case
          • +02h. "Snow Load" - AutoPIPE Load Case
          • 02i. "Thermal Bowing" - AutoPIPE Load Case
          • +02k. "Response / Force Spectrum Loads" - AutoPIPE Load Case
          • +02n. "Harmonic" - AutoPIPE Load case
          • 02p. "Time History" (M1-M50) - AutoPIPE Load Case
          • 02s. "Buoyancy" - AutoPIPE Load Case
          • +02t. "Wave" - AutoPIPE Load Case
          • +02u. "Fluid Transient" - AutoPIPE Load Case
          • 02v. "Steam Relief" - AutoPIPE Load Case
          • +02w. "Thermal Transient Analysis" (TTA) - AutoPIPE Load Case
          • +03a. "Gravity" - AutoPIPE Load Case
          • +03b. "Pressure" - AutoPIPE load case
          • 03c. "Temperature" - AutoPIPE load case
          • +03d. "SAM" (Seismic Anchor Analysis) - AutoPIPE load case
          • +03e. "Fatigue" - AutoPIPE load case
          • +03f. "Xtra Data" - AutoPIPE load case
          • +03g. "Occasional" - AutoPIPE load case
          • 03h. "Distributed Load" - AutoPIPE load case
          • 04. Results From Loads and Load Sets Not Answered By Piping Code Calculations
          • +05. Combination Load Cases (Tools> Combinations dialog)
          • +06. Non-linear Load Sequencing Explained
        • +Localization (Non-English Language) - AutoPIPE
        • +Modeling Approaches in AutoPIPE
        • +Modules (i.e. Flange Analysis, Spring Hanger Selection, Rotating Equip, TTA) in AutoPIPE
        • +Piping codes - AutoPIPE
        • +Post Processing - AutoPIPE
        • +Printing - AutoPIPE
        • +Reports - AutoPIPE
        • Security
        • +Settings - AutoPIPE
        • +Stress Isometrics - AutoPIPE
        • +Technology Productivity Capabilities
        • +Warnings, Errors, Crashed, Confirm, etc.. messages in AutoPIPE
      • +Bentley AutoPIPE Nozzle (WinNOZL)
      • +Bentley AutoPIPE Vessel (powered by Microprotol)
      • +Bentley PlantFLOW
      • +Bentley PULS
    • Multi-lingual announcement from BENTLEY TECHNICAL SUPPORT.
    • Working at Home with AutoPIPE
    • +AutoPIPE Brand Learning Resources
    • +Attend a live meeting with an AutoPIPE Analyst

    01. Why are my V-stops not allowing lateral movement during a Hydrotest load case in AutoPIPE ?

    Revision Creation Date Revision Author
    Current Revision Wed, Nov 20 2019 3:03 PM Mike Dattilio
    Revision #6 Wed, Nov 20 2019 2:52 PM Mike Dattilio
    Revision #5 Thu, Mar 8 2018 12:49 PM Mike Dattilio
    Revision #4 Thu, Mar 8 2018 12:48 PM Mike Dattilio
    Revision #3 Mon, Dec 15 2014 3:39 PM Mike Dattilio
    Revision #2 Mon, Dec 15 2014 3:38 PM Mike Dattilio
    Revision #1 Mon, Dec 15 2014 3:33 PM Mike Dattilio
    • Compare Versions View current version
    Communities
    • Home
    • Getting Started
    • Community Central
    • Products
    • Support
    • Secure File Upload
    • Feedback
    Support and Services
    • Home
    • Product Support
    • Downloads
    • Subscription Services Portal
    Training and Learning
    • Home
    • About Bentley Institute
    • My Learning History
    • Reference Books
    Social Media
    •    LinkedIn
    •    Facebook
    •    Twitter
    •    YouTube
    •    RSS Feed
    •    Email

    © 2023 Bentley Systems, Incorporated  |  Contact Us  |  Privacy |  Terms of Use  |  Cookies