Bentley Communities
Site
Search
User
Site
Search
User
Product Communities
AutoPIPE
AutoPIPE Wiki
Critical and High issues released in AutoPIPE 6.0 - 6.3
Sign In
Questions about this article, topic, or product? Click here.
Critical and High issues released in AutoPIPE 6.0 - 6.3
AutoPIPE 06.03.16
110513
Tracker#:3167 - Problems in spectrum analyses may cause a crash while generating output report
110517
Tracker#:3171 - Stream function messages do not clearly indicate the validity of results
110404
Tracker#:3056 - Current velocity and marine growth data may not always be initialized properly
110427
Tracker#:3079 - Cannot close error message E38-25 if pipe size is not valid for valve type
110383
Tracker#:3034 - Incorrect number of TIH files causes large time history ZPA reactions
111436
Tracker#:2795 - Program gives very large results for long duration time history load
111444
Tracker#:2803 - ZPA or missing mass option may cause a memory error during dynamic analyses
AutoPIPE 06.02.12
111401
Incorrect effective branch wall thickness for B31.1 reduced outlet tees
103566
Guide support results on a vertical line may be inconsistent with gap directions
111355
Wide miter elbow has the wrong B2 value for NC and ND codes
103584
Rigid support response to time history loads are not always accurate
103610
Incorrect response spectrum accelerations reported using ZPA
103612
Rigid support response to force spectrum loads are not always accurate
103734
Zero support reactions in force spectrum analysis except for last load case
103629
Using static correction methods for some dynamic analyses produces no difference
103588
Missing time history loads after using Fluid Transient command
AutoPIPE 06.01.09
103535
Insert/flange over a range in non-english units gives incorrect flange weights
103492
Paste may cause bends to have connectivity errors & invalid pipe properties
103466
Inserting a support at a tee or junction point may crash the program.
101643
Mass or soil points in flanged bend change bend flexibility
101489
Models with segments with only a single bend point can crash the program
101499
Edit/Copy can crash the program with frames connected to tee points
101530
Flexible joints of different sizes are imported from Autoplant as one size
101258
Using mmetric or metric units with BS7159 code gives incorrect modulus values
101446
When modifying temp. in SI units, hot allowable stresses may not be updated
101447
Soil points from a Copy/Paste operation may be invalid
101465
Biljaard cylindrical and spherical vessel stiffnesses are lower than expected
101467
Flexibility for flanged bend incorrect when adding a mid point
101261
Tee and continuation points may be disconnected after consistency check
101268
Modify operating loads with blue changes may incorrectly change Temp/Pres/All
101272
Hoop stress at reducers may use the wrong pressure in interactive code scan
101285
Thickness dependent hot allowable stresses may not be updated
101286
A bend midpoint may become disconnected causing abnormal program termination
101231
For models > 400 Kb, Display/Animate-Displ/Modes may corrupt model or crash
101233
DNV User "combined" code combinations do not have Hoop & Long cases
101256
Selecting laminate type or reference is not updating material properties
101257
The hot modulus is calculated incorrectly for the BS7159 code option
101534
Branch sizes at olets are imported from Autoplant incorrectly
101546
Certain loads are omitted from hydrotest case when load cases are not analyzed
101550
Beam beta angle may be incorrect for vertical frame members
101575
After delete points & consistency check, single segment tees may be corrupted
101579
Supports on bend midpoints/frames & all soil deleted during consistency check
101505
Number of automatic mass points over a span may be incorrect
101491
Inserting a run point before the current point may corrupt the P&T data
AutoPIPE 06.00.16
110401
Analysis results for deep water wave loads may be too large at the seabed
102934
Analysis may crash if Hydrotest P/T loadcase is > 1 and rigid pipes defined
102932
Invalid combinations can be created in Result\Code\User and Result\Other\User
102927
Grouping with missing mass may cause incorrect response spectrum results
102922
Selecting both beam and frame points with Edit\Text open may cause crash
102880
Edit/Copy of a single point component causes the program to hang
101204
Added mass points may affect cut short results
101075
Incorrect forces and moments when anchor attached to flex joint
101074
The pressure extension calculated for valves is incorrect
101073
CSAZ184 piping code does not calculate equivalent tensile code stresses
101072
Models with more than 400 segments may crash if view/segment is used
See Also
Critical and High issues released in version
Bentley AutoPIPE
critical
06.00.16
06.03
06.02
AutoPIPE
06.02.12
Known Issues
06.01
06.01.09
06.03.16
High
defect
06.00
Released in Version
Share
History
More
Cancel
Created by
Mike Dattilio
When:
Thu, Oct 20 2016 9:48 AM
Last revision by
Mike Dattilio
When:
Tue, Jan 10 2017 10:56 AM
Revisions:
5
Comments:
0
Recommended
Related