Bentley Communities
Bentley Communities
  • Site
  • User
  • Site
  • Search
  • User
AutoPIPE
  • Product Communities
AutoPIPE
AutoPIPE Wiki 19. Why does the Wind direction Dx, Dy, Dz values change on the Wind Profile dialog in AutoPIPE?
    • Sign In
    • -Pipe and Vessel Stress Analysis - Wiki
      • +ADL PIPE
      • -Bentley AutoPIPE
        • +- General Information about AutoPIPE
        • +- NEW User Guide for AutoPIPE
        • +- Technical Support - AutoPIPE
        • +Batch Processing, ITS, and ATS using AutoPIPE
        • AutoPIPE QA&R program
        • +Download - Install - Release Notes - AutoPIPE
        • +File / Model Management using AutoPIPE
        • +General - AutoPIPE
        • +Graphics - AutoPIPE
        • +Grids (Input & Results) - AutoPIPE
        • +Import and Export - AutoPIPE
        • +Known Issues in AutoPIPE (Enhancements, defects, etc..)
        • +Libraries - AutoPIPE
        • +License AutoPIPE -
        • -Loads and Load Sets - AutoPIPE
          • 01. Animate Load cases - AutoPIPE
          • 02a. Load Case Descriptions in AutoPIPE
          • +02b. Static Analysis in AutoPIPE
          • +02c. Dynamic Analysis in AutoPIPE
          • +02e. "Hydrotest" - AutoPIPE Load Case
          • +02f. "Static Earthquake" - AutoPIPE Load Case
          • -02g. "Wind" - AutoPIPE Load Case
            • 05. How is the ground elevation determined for a Wind load case in an AutoPIPE model?
            • 06. How to input a Wind profile using Wind Velocity instead of Wind Pressure in AutoPIPE?
            • 07. How to account for East and West wind in both +ve and -ve directions in AutoPIPE?
            • 08. Will "Inclined" wind direction set to off global axis take care of user required eccentric, torsional, or pitched loading of FPSO or off shore platforms in AutoPIPE?
            • 09. Should the Wind Shape Factor Multiplier be 1 or 0.7 when using the ASCE wind specification type in AutoPIPE?
            • 10. How to apply the same wind speed over the entire model in AutoPIPE?
            • 11. How can the pipe movement be greater than the support gap setting for wind load combinations in AutoPIPE?
            • 12. Is the pressure used in a wind profile the basic pressure (i.e. acting on a plate), or do I have to adjust the pressure for a pipe when inputting the figure in AutoPIPE?
            • 13. What is the interpretation for annual probability and its relevance for determining wind load in AutoPIPE?
            • 14. Is there any way to consider friction only the expansion case but not in any occasional AutoPIPE Wind loads?
            • 15. Does AutoPIPE count pipe insulation thickness towards the effective diameter for wind/wave force calculations?
            • 16. Where can one find information on ASCE 7 Wind speeds for AutoPIPE?
            • 18. Why does the wind load appear that is not being applied to the model in AutoPIPE?
            • 19. Why does the Wind direction Dx, Dy, Dz values change on the Wind Profile dialog in AutoPIPE?
            • 20. Are ASCE7 - 2010 Wind loads ASD or LRFD in AutoPIPE
            • 21. Model Wind Sway On A Pipe Rack in AutoPIPE
            • 22. How to convert from wind loads from MPH to PSF in AutoPIPE?
            • 23. What is the value of ASCE 7 Wind load setting "Cf" when value is set to Automatic in an AutoPIPE model?
            • 24. Using ASCE 7 Is basic wind speed assumed to be sustained or a gust in an AutoPIPE model?
            • 25. How are Wind loads applied to Constant Spring supports in AutoPIPE?
            • 26. Is Kd term missing from ASCE 7-10, so Is this mix of 7-05 and 7-10 for AutoPIPE Wind load?
            • Nonlinear wind load analysis in AutoPIPE
          • +02h. "Snow Load" - AutoPIPE Load Case
          • 02i. "Thermal Bowing" - AutoPIPE Load Case
          • +02k. "Response / Force Spectrum Loads" - AutoPIPE Load Case
          • +02n. "Harmonic" - AutoPIPE Load case
          • 02p. "Time History" (M1-M50) - AutoPIPE Load Case
          • 02s. "Buoyancy" - AutoPIPE Load Case
          • +02t. "Wave" - AutoPIPE Load Case
          • +02u. "Fluid Transient" - AutoPIPE Load Case
          • 02v. "Steam Relief" - AutoPIPE Load Case
          • +02w. "Thermal Transient Analysis" (TTA) - AutoPIPE Load Case
          • +03a. "Gravity" - AutoPIPE Load Case
          • +03b. "Pressure" - AutoPIPE load case
          • 03c. "Temperature" - AutoPIPE load case
          • +03d. "SAM" (Seismic Anchor Analysis) - AutoPIPE load case
          • +03e. "Fatigue" - AutoPIPE load case
          • +03f. "Xtra Data" - AutoPIPE load case
          • +03g. "Occasional" - AutoPIPE load case
          • 03h. "Distributed Load" - AutoPIPE load case
          • 04. Results From Loads and Load Sets Not Answered By Piping Code Calculations
          • +05. Combination Load Cases (Tools> Combinations dialog)
          • +06. Non-linear Load Sequencing Explained
        • +Localization (Non-English Language) - AutoPIPE
        • +Modeling Approaches in AutoPIPE
        • +Modules (i.e. Flange Analysis, Spring Hanger Selection, Rotating Equip, TTA) in AutoPIPE
        • +Piping codes - AutoPIPE
        • +Post Processing - AutoPIPE
        • +Printing - AutoPIPE
        • +Reports - AutoPIPE
        • Security
        • +Settings - AutoPIPE
        • +Stress Isometrics - AutoPIPE
        • +Technology Productivity Capabilities
        • +Warnings, Errors, Crashed, Confirm, etc.. messages in AutoPIPE
      • +Bentley AutoPIPE Nozzle (WinNOZL)
      • +Bentley AutoPIPE Vessel (powered by Microprotol)
      • +Bentley PlantFLOW
      • +Bentley PULS
    • Multi-lingual announcement from BENTLEY TECHNICAL SUPPORT.
    • Working at Home with AutoPIPE
    • +AutoPIPE Brand Learning Resources
    • +Attend a live meeting with an AutoPIPE Analyst

     
     Questions about this article, topic, or product? Click here. 

    19. Why does the Wind direction Dx, Dy, Dz values change on the Wind Profile dialog in AutoPIPE?

    Applies To
    Product(s): AutoPIPE,
    Version(s): ALL
    Environment: N/A
    Area: Load
    Original Author: Bentley Technical Support Group

    Problem:

    W2 is entered as per image below,

    Select the OK button and reopen the same load case,  AutoPIPE automatically changes the 1, 1 into 0.707, 0.707. WHY?

    Furthermore, if you change the value and reopen the dialog screen the original 0.707 settings are updated to random values below 1.0. WHY?

    Solution:

    First while on this dialog, press the Help button and select the Hyperlink for "Wind Direction", when the help opens for this specific topic, the answer to the first question is answered by the last sentence of the paragraph "Upon saving the inclined direction vector..."

    Second, to answer why the program is mysteriously updated to some values other than 1.0 or 0.707; answer, because the value was not correctly accepted by the dialog and the previous value is still being applied. On this and other dialogs, after updated a dialog field value, press the TAB keyboard key before using the mouse to select the OK button. Otherwise the program will ignore the new settings and use the original values that was originally entered before the update.

    Again, solution read the online help to know why the values of Dx=1.0 and Dy = 1.0 are being changed, and always use the TAB  keyboard key after entering any data into any dialog.

    See Also

    Modeling "Wind" - Load Case

    Bentley AutoPIPE

    • AutoPIPE
    • Win Profile
    • Direction
    • Wind
    • Share
    • History
    • More
    • Cancel
    • Mike Dattilio Created by Bentley Colleague Mike Dattilio
    • When: Thu, Mar 9 2017 3:54 PM
    • Revisions: 1
    • Comments: 0
    Recommended
    Related
    Communities
    • Home
    • Getting Started
    • Community Central
    • Products
    • Support
    • Secure File Upload
    • Feedback
    Support and Services
    • Home
    • Product Support
    • Downloads
    • Subscription Services Portal
    Training and Learning
    • Home
    • About Bentley Institute
    • My Learning History
    • Reference Books
    Social Media
    •    LinkedIn
    •    Facebook
    •    Twitter
    •    YouTube
    •    RSS Feed
    •    Email

    © 2023 Bentley Systems, Incorporated  |  Contact Us  |  Privacy |  Terms of Use  |  Cookies