How to add Nozzle size on Isometric?

When we extract the isometric which is connected to Equipment Nozzle, normally it shows the Nozzle Tag, Nozzle Rating and Nozzle facing in continuation.

But I want to add Nozzle size as well in continuation. Can you please help me to achieve that?

We are using AutoPLANT SS4.

Thanks and Regards

Sandip Badgujar

Parents
  • Hello Sandip, 

    Are you trying this with OpenPlant Isometrics Manager or an ISOGEN? we have a similar content available in context with OpenPlant Isometrics Manager. Please have a look below:

    http://communities.bentley.com/products/plant/design___engineering/w/plant_design_and_engineering__wiki/17255.add-nozzle-rating-and-facing-information-in-continuation-nozzle-expression 

    Regards,
    Rahul Kumar

    Regards,

    Rahul Kumar

    Product Engineer – Global Technical Support | Community Moderator

  • Hi Rahul

    As mentioned in my previous post, we are using AutoPLANT SS4 which uses isogen to extract the isometric. If I am not wrong OpenPlant Isometric Manager is introduced in AUtoPLANT SS5. Please help me to achieve it using isogen.

    Regards
    Sandip Badgujar
  • Hello Sandip,

    Could you please try following steps:
    1. Open C:\Program Files (x86)\Bentley\Plant V8i\Modules\Base\xchg\pcf\eqpnozz.ebs.
    2. Go to Line 85 and insert the code below under the code for `// Nozzle Facing:

    `// Main_size
    status = at_Component_getstring (tempStr, compID, "NPS_MAIN") If ((status = AT_SUCCESS) And (Len(tempStr) > 0)) Then
    refText = refText + "$MAIN_SIZE " + RTrim$ (tempStr) End If


    3. Save and close the file.

    Hope this helps.

    Regards,
    Abhijit Bute

      


     

    Answer Verified By: Artiom J 

  • Hi Sandip, 

    In order to get nominal nozzle size in continuation reference message the following ebs file should be edited:

    C:\Program Files (x86)\Bentley\Plant V8i\Modules\Base\xchg\pcf\eqpnozz.ebs 

    As well same file could be stored on project level PROJECT_ROOT\Config\Modules\Base\xchg\pcf\eqpnozz.ebs 

    Add below code to eqpnozz.ebs starting from line 92:

    '// Nozzle Size
    status = at_Component_getPortND(tempStr, compID, "NP1")
    If ((status = AT_SUCCESS) And (Len(tempStr) > 0)) Then
    refText = refText + "$SIZE " + RTrim$ (tempStr)
    End If


    As a result you should get following iso output:

    The message is being split due to amount of reference information. 

    I hope this will be useful. 
    Please let me know if you will have further questions. 

    Kind Regards, 
    Artiom



    Answer Verified By: Artiom J 

Reply
  • Hi Sandip, 

    In order to get nominal nozzle size in continuation reference message the following ebs file should be edited:

    C:\Program Files (x86)\Bentley\Plant V8i\Modules\Base\xchg\pcf\eqpnozz.ebs 

    As well same file could be stored on project level PROJECT_ROOT\Config\Modules\Base\xchg\pcf\eqpnozz.ebs 

    Add below code to eqpnozz.ebs starting from line 92:

    '// Nozzle Size
    status = at_Component_getPortND(tempStr, compID, "NP1")
    If ((status = AT_SUCCESS) And (Len(tempStr) > 0)) Then
    refText = refText + "$SIZE " + RTrim$ (tempStr)
    End If


    As a result you should get following iso output:

    The message is being split due to amount of reference information. 

    I hope this will be useful. 
    Please let me know if you will have further questions. 

    Kind Regards, 
    Artiom



    Answer Verified By: Artiom J 

Children
No Data