OpenPlant V8i Component Scripting C# Settings for the values FACING

RE: OpenPlant V8i Component Scripting C# Settings for the values FACING

Vitaliy Malikov — Tue, 05 Nov 2019 07:43:37 GMT

communities.bentley.com/.../4135.testSpec.zip

RE: OpenPlant V8i Component Scripting C# Settings for the values FACING

Rahul Kumar — Mon, 04 Nov 2019 02:41:55 GMT

Hi Vitaliy,

No, its opposite

If NOMINAL_DIAMETER or END_PREPARATION are not same for components then it can allow you to have different FACING.

E.g a valve of DN100 size having should have end prep Flanged at both end, hence taking facing value same. To cater different facing End Prep of any end should changed to different End Prep, other than Flanged

Or If you have Flanged end component but Nominal dia available as DN100/DN80 then also you can change it different FACING.

HTH,

RE: OpenPlant V8i Component Scripting C# Settings for the values FACING

Vitaliy Malikov — Sat, 02 Nov 2019 08:16:24 GMT

Hi Rahul,

Thanks for reply.

As I understood you correctly, if I need to set two different facing value to one component MAIN_PORT & RUN_PORT value of NOMINAL_DIAMETER must be the same?
But if MAIN_PORT & RUN_PORT value of NOMINAL_DIAMETER are different?

Regards, Vitaliy

RE: OpenPlant V8i Component Scripting C# Settings for the values FACING

Rahul Kumar — Fri, 01 Nov 2019 09:45:23 GMT

Hi Vitaliy,

What I understood here is - You need to set two different facing value say RF-FF to one component.

Placement logic defined as - FACING property should be same if MAIN_PORT & RUN_PORT value of NOMINAL_DIAMETER or END_PREPARATION matches with each other.

Hence in case you want to have same nominal dia, you need to change End Preparation detail for RUN_PORT and can try it out.

Hope it helps here.

RE: OpenPlant V8i Component Scripting C# Settings for the values FACING

Gaurav.Gundecha — Thu, 31 Oct 2019 13:50:42 GMT

tesSpec mdb is blocked by the website. Can you please rename the extension of mdb to something else like .txt and upload it again/?

Thanks.

RE: OpenPlant V8i Component Scripting C# Settings for the values FACING

Vitaliy Malikov — Wed, 30 Oct 2019 04:31:36 GMT

Hi!
Thanks for reply.

I attach the archive with C# project, the archive with schemas (these are schemes where I did some changes), test spec and description about adding a new element in Bentley Class Editor.
I created the element in OPModeler_Imperial project.

communities.bentley.com/.../SafetySpringValve.zip communities.bentley.com/.../6505.Schemas.zip
communities.bentley.com/.../testSpec.mdb communities.bentley.com/.../Description.txt

Regards, Vitaliy

RE: OpenPlant V8i Component Scripting C# Settings for the values FACING

Gaurav.Gundecha — Mon, 28 Oct 2019 16:36:44 GMT

Can you share your C# Project? Facing values are read from spec and your spec should have its columns mapped to correct Fluid Port properties for Facing.

If you have customized your schemas, please share your V8i OPM project too, so that we can take a look.

Thanks,

RE: OpenPlant V8i Component Scripting C# Settings for the values FACING

Vitaliy Malikov — Sat, 26 Oct 2019 08:59:02 GMT

Hi Swapnil,

Thanks for reply.
When and how I can find out about the results?

Regards, Vitaliy

RE: OpenPlant V8i Component Scripting C# Settings for the values FACING

Swapnil Joshi — Thu, 24 Oct 2019 11:54:31 GMT

Hi Vitaliy,

Thank you for posting query on Bentley Plant Forum.

We have forwarded your concern to the concerned person.

Regards | Swapnil