STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

RE: STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

Kris Sathia — Wed, 02 Nov 2022 14:18:33 GMT

By primary, I presume you are referring to pure component load cases. It doesn't make sense to design for such load cases. Designing for a load case that represents just wind, or pure seismic means you will have a lot of de-stabilizing effect due to lateral loads, and no stabilizing effect from the vertical loads to accompany that. If you do this, you may end up with much larger foundation sizes than warranted, or a failure when there shouldn't be one.

It makes sense to solve just for the load combinations since they represent the simultaneous action of gravity with live, gravity with wind, gravity with seismic, etc.

This principle applies to all types of foundations - isolated footings, pilecaps, mats, etc.

RE: STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

Piyush Mehta — Wed, 02 Nov 2022 13:09:47 GMT

Are we required to remove the primary load cases? Usually I include the primary load cases for the isolated footing job and that works fine.

RE: STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

Kris Sathia — Wed, 02 Nov 2022 10:09:12 GMT

If you want the footing to be designed for just load cases 10 to 79, you need to

a) Edit the job and remove load cases 1 to 9 frrom the list of "Selected Load Cases".

b) Load cases 10 to 37 should have their type changed from Primary to Ultimate.

c) Load cases 38 to 79 should have their type changed from Primary to Service.

For (b) and (c), see this

https://communities.bentley.com/products/ram-staad/w/structural_analysis_and_design__wiki/39223/applying-load-case-types-to-load-cases-or-combinations-in-batches

RE: STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

Piyush Mehta — Tue, 01 Nov 2022 01:19:27 GMT

I have the latest version 9.7.1 but still I am getting the same error.communities.bentley.com/.../8611.Bus_5F00_Support_5F00_Design_5F00_BSF2_5F00_foundation.sfa

RE: STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

Alhec Briones — Mon, 23 Nov 2020 13:21:07 GMT

Hey Kris Sathia! I'd just sent you a private message. Thanks!

RE: STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

Kris Sathia — Mon, 23 Nov 2020 04:37:07 GMT

In the current version of SFA - 9.4.0.20 - this model runs successfully. See the attached output.

In older versions, if the maximum size limit was reached on any of the 3 dimensions - length, width or thickness, the program would stop iterations. In the current version, if the limit is reached on any of those three, the program will perform another trial by increasing the size of those sides which have not reached their limit.

communities.bentley.com/.../2678.calc-sheet.pdf

RE: STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

Alhec Briones — Sun, 22 Nov 2020 04:56:23 GMT

Please help me my fellow engineers.

RE: STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

Alhec Briones — Sun, 22 Nov 2020 04:56:01 GMT

This is the imported staad file. Please see attached file below. communities.bentley.com/.../TRIAL-2_2D00_R3.std

RE: STAAD FOUNDATION ADVANCED (DESIGN OF COMBINED FOOTING)

Alhec Briones — Sun, 22 Nov 2020 04:54:56 GMT

Please send help, my fellow engineers.