https://communities.bentley.com/products/ram-staad/f/ram-staad-forum/95534/staad-error-messageDear Sir/Sirs, Am new to STAAD Pro. I have designed an intake using plate model. Assigned loads. When i try to analyse following error appears. PRIMARY LOAD CASE CAN ONLY BE ADDED IF SET NL COMMAND IS USED. How can i rectify. Please help. en-USTelligent Community 12https://communities.bentley.com/thread/278417?ContentTypeID=1Tue, 18 Mar 2014 09:37:33 GMT6dad98f5-dbc9-4c4d-a9ba-e9da8dc6aa8e:de3f0efd-6f80-4382-98df-0aa305a9303bShany<p>Happy to help.</p><div style="clear:both;"></div>https://communities.bentley.com/thread/278405?ContentTypeID=1Tue, 18 Mar 2014 08:42:59 GMT6dad98f5-dbc9-4c4d-a9ba-e9da8dc6aa8e:e49199b0-69e6-486e-83fa-d58678243d5fVaradha Rajan<p>Dear sir,</p> <p>Now it works. Thank u a lot sir. But it showed about 9 warnings that iteration limits does not converge and suggested to use set iterlim command. I have under stood and cleared that too in the same way. Thanks again</p><div style="clear:both;"></div>https://communities.bentley.com/thread/278397?ContentTypeID=1Tue, 18 Mar 2014 07:21:32 GMT6dad98f5-dbc9-4c4d-a9ba-e9da8dc6aa8e:daff82fe-b57b-49a6-9b28-61532c93afe7Shany<p>When a model contains more than 25 load cases, with some being solved using one set of conditions and others being solved with another set of conditions, a command known as &quot;SET NL nn&quot; is required where nn is a number which is at least equal to the number of load cases. </p> <p>In this case, this condition is achieved by the CHANGE command that you have used after every analysis. As it turns out from the STAAD &nbsp;model &nbsp;you have attached, the total number of load cases is beyond the default number of load cases the space has been reserved for. Hence, I have used the SET NL command. This command instructs the program to set aside additional memory space for information to be added later.</p> <p>Open the Staad Editor File, and before the JOINT COORDINATE command line, add the command SET NL 100 (for this model I have added 100)</p><div style="clear:both;"></div>https://communities.bentley.com/thread/278395?ContentTypeID=1Tue, 18 Mar 2014 06:36:18 GMT6dad98f5-dbc9-4c4d-a9ba-e9da8dc6aa8e:b239e021-0b9c-41eb-99d6-6a2611d4c11aVaradha Rajan<p>How can i manually use the command. I am unable to understand the syntax given in help</p><div style="clear:both;"></div>https://communities.bentley.com/thread/278394?ContentTypeID=1Tue, 18 Mar 2014 06:34:36 GMT6dad98f5-dbc9-4c4d-a9ba-e9da8dc6aa8e:a74fcdc7-316e-4b64-936c-2d55349f6b5aVaradha Rajan<p>I have attached the model</p><div style="clear:both;"></div>https://communities.bentley.com/thread/278393?ContentTypeID=1Tue, 18 Mar 2014 06:23:23 GMT6dad98f5-dbc9-4c4d-a9ba-e9da8dc6aa8e:490df131-8695-4720-9f2b-3daf92a7a9b1Shany<p>The program is not able to see the number of load cases that has been specified beyond the CHANGE command. Hence, it reserves space for a default number of load cases. If the specified number of load cases is beyond the default number, the program would not be able to accommodate that. I presume,in your model, &nbsp;the total number of load cases is beyond the default number of load cases the space has been reserved for. Hence, you need to manually reserve the space for the existing number of load cases using the SET NL command.</p><div style="clear:both;"></div>https://communities.bentley.com/thread/278392?ContentTypeID=1Tue, 18 Mar 2014 06:21:45 GMT6dad98f5-dbc9-4c4d-a9ba-e9da8dc6aa8e:7c27527c-290a-41c6-a1e6-7d20646c700bShany<p>Please send us the model.</p><div style="clear:both;"></div>