• Deflection

    Hello, Guys! I have added the TRACK 2 command along with the DFF to see the in-depth details of deflection. May I know if this, please see attached picture, can be seen somewhere in the postprocessing? Also, how can I get the deflection of the entire…
  • mat foundation for a tank

    Hello every one I'm trying to design mat foundation for a tank and the analysis result shows 0 moment in x and y. can anyone help me? I attached the file of staad to check it. Thank you
  • THE MEMBER 1 CAN NOT BE DESIGNED FOR BENDING AS THIS VERSION DOES NOT SUPPORT THE SELECTED SECTION, SELECT ANOTHER TYPE OF SECTION

    Why this keeps appearing, Guys? I got the same warning for HSS Rectangle standards. Can somebody help me please.
  • Section database take too much time in Staad CE 12 & ALSO IN v2023

    Section database take too much time in Staad CE 12 & ALSO IN v2023
  • "DEFINE" COMMANDS FOR LOAD GENERATION SHOULD BE PROVIDED BEFORE SPECIFYING PRIMARY LOAD CASES.

    Tell me how can I get rif of this error please. DEFINE UBC ACCIDENTAL LOAD ZONE 0.4 I 1 RWX 3.5 RWZ 3.5 STYP 4 CT 0.0488 NA 1.2 NV 1.6 SELFWEIGHT 1.1 UNIT METER KN DEFINE WIND LOAD TYPE 1 WIND_PEDESTRIANBRIDGE <! STAAD PRO GENERATED DATA DO NOT MODIFY…
  • STAAD's Displacement

    Is this a normal displacement in STAAD.Pro Connect Edition? I am designing a pedestrian footbridge and I happened to encounter this displacement in a certain load case?
  • SHEAR FORCE DAIGRAM IS CHANGED IF WE CHANGE THE BEAM INCIDENCE

    I MODEL A BEAM A BEAM OF 12 M SPAN IN WHICH THE SUPPORTS ARE ASSIGNED AT 8 M C/C AND REST 2.2 M FROM EITHER SIDE IS CANTILEVR , NOW IF I CHANGES THE BEAM INCIDENCE THE SHEAR FORCE DIAGRAM IS CHANGED (REVERSED) WHILE LOADING POINT IS SAME
  • *** ERROR *** ABOVE COMMAND IS NOT RECOGNIZED. LINE IGNORED. anyone plz help me

    *** ERROR *** ABOVE COMMAND IS NOT RECOGNIZED. LINE IGNORED. i cant understand
  • How do select the angle between truss members?

    I want create a truss I chose one from structure wizard but I want a specific angle between truss members at end points (usually referred as alpha) where I can change the default settings for this?
  • Wind Load on Tapered Section -reg.

    Dear Colleagues, current version : STAAD.Pro CONNECT Edition - Version 22.12.00.142 there was a situation where we had to find out the lateral forces due to wind on a light pole (tapered profile) and provide suitable support for the same. Wind was…
  • staad.pro connect edition version 22.10.00.153

    Dear Sir, Our Project Requirement: 600’ x 200’ x 43’ PEB Warehouse We’ve taken a Model of 157’ x 200’ x 43’ for STAAD Analysis as a similitude model with EJ For the last 45 days, our design engineers have been carrying out the design work of the…
  • ERROR: MEMBER # 3 IS NOT A VALID COLD-FORMED STEEL SECTION. E-10 - in Staad.pro

    Hi Staad master sirs, I’m Trying with the Staad.pro model of a Rack system with Economic solutions - which consists of Hot Rolled Sections + Cold-Formed Steel sections, by using IS800 + IS801. My entire members are only supposed to be Designed as Hot…
  • Model a curved beam (Displacement)

    I am modeling a curved roof and used structure wizard to break the curve into smaller segments of a straight line. I can run the model and get the proper reaction and beam results that I previously estimated. The displacement is much greater than I expected…
  • Error while updating column design in RCDC

    An error is showing while updating the column design in RCDC as shown below. please provide the solution .
  • STAAD.Pro: how to input Lb for AISC 360 steel beam design

    Dear all, I am modelling a simple roof steel frame and the steel beam design is not passing the design check for AIS-360 LRFD LBT I have defined UNT and LY for the steel beam and it should meet the condition of Lp < Lb < Lr, however the design results…
  • Error Staad Cargas muertas

    Hola tengo este problema en mi computadora, al asignar cargas muertas a mi edificio se producen estas áreas fuera del modelo que no me dejan trabajar, he buscado ayuda pero nadie me da una respuesta, aparentemente solo sucede en mi computadora por que…
  • THE COMPRESSIVE AXIAL STRESS IN MEMBER # 1049 EXCEEDS 0.08FCK AT SECTION 0.0 MM FOR LOAD # 216 AS PER CL 6.1 OF IS-13920 2016.

    Dear All, I got lot of warnings for the beams that the compressive axial stress in member exceed 0.08fck. What is the solution for that i have got lot of warnings regarding this. Please suggest me Thanks & Regards, Anirudh
  • how to connect beam to column

    how to connect beam to column. column size is 4m x .850m, baem size 0.750m x 0.400m. see the attach file image. Yellow line is the column. .
  • Design of Solid slab (Conventional slabs)

    Hello Everyone For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…
  • Dummy beam

    Hello Everyone. I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?
  • Staad Plant Foundation: Why footing size too large by using IS code?; While US code give appropriate size!

    1) Please Suggest modification, correction in my Staad Foundation file, for since I am Getting very large sizes in (approx Twice in Plan, 20 time in thickness). a) Used IS code /IS 456, Si units, compared with US code SI units, Code ACI 318 -14 b) Loads…
  • Missing Surfaces in STAAD Analytical Model From Physical Model

    I have a physical model in STAAD.Pro CE as shown in the first image. The central portion of the surface disappears when I view/generate an analytical model (second image). How do I bring the whole model to the analytical model space? Also, beams under…
  • RC designer beam fail

    Hello , I have done analysis and tried RC designer . the columns are safe. Beam summary show fails. please help me into this . cross section of beam is large i assume. 8284.COLLEGE PROKECT.STD
  • Gantry crane design

    Does anybody designed Gantry crane using STAAD.Pro? Can anybody explain how can i assign whole surface of the rail on the ground as fixed? do i need to divide the rail in to small parts and assigned those nodes as fixed? or do i need to design Gantry…
  • STAAD.Pro Connect edition pushover analysis for concrete structure

    Can STAAD.Pro Connect edition perform pushover analysis for concrete structure?