How did know the exact coordinate of the partition wall?? please help me

Please, someone can help me. One error says *** ERROR *** ABOVE COMMAND IS NOT RECOGNIZED. LINE IGNORED. don't know what to do. RCD 4 Storey.std

sabbir ahmed -static - 07.05.22.std SOMEONE PLEASE REPLY, Calculation sheet is not available as design has failed, why it is showing ? sabbir ahmed -static - 07.05.22_foundation.xml

Please go through the file and reply ASAP. I am waiting.Please go through the file and reply ASAP. I am waiting. sabbir ahmed -static.std

As you can see here the wind load does not show on the rest of the Z+ building face i tried to play with the ranges but it does not work the part where it does not show is a cantilivar beam the left side of the photo down here

this is the code STAAD SPACE START JOB INFORMATION ENGINEER DATE 09-Apr-22 END JOB INFORMATION INPUT WIDTH 79 UNIT METER KN JOINT COORDINATES 1 0 0 0; 2 0 12.085 0; 3 -1.05865e-015 0 5.763; 5 -2.11729e-015 0 11.526; 7 -3.17594e-015 0 17.289; 8 -3…

6201.Project 1 new.std

How can I delete some supports? I have given support and nodes very close to another nodes and support by mistake. When I delete these wrong support, my file gets corrupt. Please help. 0677.Project 1 new.std

6278.Project 1 new.std

Dear Team I am working with the Staad model for buckling analysis . The buckling load factor is given by the staad after the analysis , wanted to understand the how to manually check the Buckling load factor using Critical Euler equation . I have manually…

Good day Everyone! I have several warnings in what I'm trying to design. I designed this model in STAAD TRUSS since this is a truss. Below are the details. Thanks in advance. P R O B L E M S T A T I S T I C S -----------------------------…

Hello, I had a question regarding this simple circular tunnel model shown below. I have the following modeled to check the shear SQY. I know I'm missing something simple here so I hope I can get some help. L=100 ft (total longitudinal length)…

Hello Everyone For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…

Hello Everyone. I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?

Dear sir, As per the attached file when i check the moment diagram for secondary beams 356*171*45 .staad showing as these beams are pinned and in my model,I am considering them as a fixed .Why moment is not coming at the end nodes? roof.std …

How to rectify this failure known as 'Detailing failure' in RCDC

Dear sir, I am doing the analysis of cable but the reactions are coming with an extreme value like 66kn along x. There is no any weight on the cable only self-weight is considered. Kindly explain to me why reactions are so conservative. Also, guide…

How does Moment distribution and release for beams work in STAAD Pro ? While designing Secondary Beams, I’m releasing the moments MX, MY, MZ to a 100% at their ends. if I keep the ends fixed, I get a hogging moment say ‘ X ’ kN-m at the ends. However…

Dear sir, I am doing cable analysis to find out the reactions to design the base plate. But I am getting reactions only in y-direction. There should be also some reactions in the x-direction. Kindly guide.Staad file is also attached. The cable…

Is there anyway to get the member group names into the mdb database generated along with SQL query. It would be much easier to analyze the results then.

Sir, the bottom chord of my trusses is failing due to compression at wind load upward alone load case 5. But i want to ignore this case which will never happen alone due to dead load of 1 kn/m2 on the roof.I want to check my steel with load combinations…

Dear all Greetings. I have model here contains of the main frame "rafter +column" (for gravity load +lateral load) + the lateral system (strut pipe +x bracing). my question is :-----design output shows the highlighted member fail due to gravity…

Dear All, Currently i'm designing a gantry crane. 1. I have assigned the loading from Crab to the gantry beam as moving load (Shows in Red color), But i have no idea how to assign the loading (Shows in Green color) when gantry crane is moving along…

Dear sir, I want to camber a steel beam . I am putting the value 750 (length/offset =30000mm/40mm(we need to camber it 40 mm)) and respect value 1.6 but results are still same with deflection 50mm .Why deflection is not decreasing? Kindly also guide…

Dear sir, In staad pro how we can camber a beam . stad file also attached.I want to camber this beam 20mm .Is it possible in staad? 6472.Str1.std