I am using a square section by TATA STRACTRA one on top of another.

sabbir ahmed -static - 07.05.22.std SOMEONE PLEASE REPLY, Calculation sheet is not available as design has failed, why it is showing ? sabbir ahmed -static - 07.05.22_foundation.xml

this is the code STAAD SPACE START JOB INFORMATION ENGINEER DATE 09-Apr-22 END JOB INFORMATION INPUT WIDTH 79 UNIT METER KN JOINT COORDINATES 1 0 0 0; 2 0 12.085 0; 3 -1.05865e-015 0 5.763; 5 -2.11729e-015 0 11.526; 7 -3.17594e-015 0 17.289; 8 -3…

Hola tengo este problema en mi computadora, al asignar cargas muertas a mi edificio se producen estas áreas fuera del modelo que no me dejan trabajar, he buscado ayuda pero nadie me da una respuesta, aparentemente solo sucede en mi computadora por que…

Hi. I recently got access to the student license of STAAD Pro. It was working well until last few days. The application is not starting. Below given screen appears and then there is no further movement in the loading. I tried re-installing the application…

Hello, I had a question regarding this simple circular tunnel model shown below. I have the following modeled to check the shear SQY. I know I'm missing something simple here so I hope I can get some help. L=100 ft (total longitudinal length)…

Hello Everyone For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…

Hello Everyone. I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?

How to create a cantilever slab without beams in the Physical modeler in STAAD connect edition?

How to rectify this failure known as 'Detailing failure' in RCDC

Dear sir, I am doing the analysis of cable but the reactions are coming with an extreme value like 66kn along x. There is no any weight on the cable only self-weight is considered. Kindly explain to me why reactions are so conservative. Also, guide…

How do I change Mton/Cm to Kn/m

Dear sir, In My attached fil,I am creating a deck slab to make my steel beams as a composite beams.But I notice deck slab somewhere missing the steel beams .some beams are not composite?Why it is happening?do I have to add that beams manually in stad…

Dear sir, In attached stad file. I am applying the dead load 2kn/m2 as floor load. 1.somewhere I am attaching two secondary beams with primary beams with the same node.is this load distributed all over the area same as 2kn/m2 or where I am having…

Hello, Is there any way that i can perform Fatigue analysis for steel member in STAAD.Pro? Thank you in advance

warehouse.zip wind calculation also in that folder.... try to fix this probem guys

Hello, I have done a beam analysis and the shear at the middle is excactly 0. When i use " SECTION 0.5 MEMB 1" the results are okay. That means in the output file "shear y" is 0 at position 0.5. But when i use SECTION command with 2 or 3 positions…

Dear sir, I designed a structure by using both method.in first method i deaigned it by composite beam method.and in second method i do it with composite deck.but by using composite beams giving lower utilization ratio than composite deck method.can…

I am analysing an RCC box girder for which some peculiar tapered sections have to be created. I created a tapered rectangular section in AutoCAD 2014. I used polyline to create the 2D and then extruded it to make it a solid 3D section. Now when I import…

I'm working in built-up column with four I sections. I'm getting some results and not sure the results are correct. Can someone please check the model is correct? Thank you. Built-Up column.STD

I have got my report, but there is no loading details like dead load, Wind loads and all... In report settings i have added Loadings, but its not showing.... Wt to do???? i want to see other load details. How to get that details?

Dear Engineers, I have working on Bridge design... Is it possible to apply moving load (HA and HB ) in Bridge deck using BS code... Can any one help me on this issue and tell me how to apply those load plz.../ I am unable to find it...

Join us for our Free seminar this Friday July 19th. Click Here for login information and a full description of Insider Skills. This weeks Topics: Wind Load Generation Floor Loading Options Seismic Load Generation Custom Section User…

hello, 705 715 START FX FZ MX MY 705 715 END FX FZ MX MY . these are the release specification given and one more think is that i my beam is incline.

Hello! I am new to ISM, and am experimenting with it as a central repository for Prostructures design and STAAD Engineering data. It seems to work at first attempt, but I am having an issue with materials. It seems that the mapping of materials from…