hello sir, I have two questions 1-when we design concrete column in a new version of staad shows area steel only in report but in old version when we design concrete column and print report shows type of column(400x400 for example), and critical…

*** ERROR *** ABOVE COMMAND IS NOT RECOGNIZED. LINE IGNORED. i cant understand

I am using a square section by TATA STRACTRA one on top of another.

sabbir ahmed -static - 07.05.22.std SOMEONE PLEASE REPLY, Calculation sheet is not available as design has failed, why it is showing ? sabbir ahmed -static - 07.05.22_foundation.xml

Please go through the file and reply ASAP. I am waiting.Please go through the file and reply ASAP. I am waiting. sabbir ahmed -static.std

As you can see here the wind load does not show on the rest of the Z+ building face i tried to play with the ranges but it does not work the part where it does not show is a cantilivar beam the left side of the photo down here

Hi, Hopefully, you are doing well. could you please help me to solve this error? this is the code below. regards, DEFINE WIND LOAD TYPE 1 WIND -Z (WINDWARD WALL) <! STAAD PRO GENERATED DATA DO NOT MODIFY !!! ASCE-7-2010:PARAMS 137.000 KMPH 0…

this is the code STAAD SPACE START JOB INFORMATION ENGINEER DATE 09-Apr-22 END JOB INFORMATION INPUT WIDTH 79 UNIT METER KN JOINT COORDINATES 1 0 0 0; 2 0 12.085 0; 3 -1.05865e-015 0 5.763; 5 -2.11729e-015 0 11.526; 7 -3.17594e-015 0 17.289; 8 -3…

Dear sir, Both stringers of staircase having same section only difference is one is created in section wizard and one is define in section table in staad.why the bending capacity of section wizard created section is less than other one.KIndly explain…

6201.Project 1 new.std

Hola tengo este problema en mi computadora, al asignar cargas muertas a mi edificio se producen estas áreas fuera del modelo que no me dejan trabajar, he buscado ayuda pero nadie me da una respuesta, aparentemente solo sucede en mi computadora por que…

Dear Team I am working with the Staad model for buckling analysis . The buckling load factor is given by the staad after the analysis , wanted to understand the how to manually check the Buckling load factor using Critical Euler equation . I have manually…

Please let me know that amendment -2 of IS1893-2016 has been updated in the staad pro connect edition. inform the version of that staad pro connect edition if updated otherwise when same will be updated .

Hello.sir i m comparative study of elevated water tank resting on sloping ground & take slope varies from 0 to upto 30degree..I have dout in staad model.. actually I already model but my result not getting correct..means as per our study base shear will…

Hello, I had a question regarding this simple circular tunnel model shown below. I have the following modeled to check the shear SQY. I know I'm missing something simple here so I hope I can get some help. L=100 ft (total longitudinal length)…

How to model, analyze, and design this reinforced concrete cantilever beam using Staad Pro?

Hi guys, im having trouble with some warnings in my staad pro file.. can someone please help me?? im having an errors of: Zero stiffness, Tension/compression and others. [Admir Islamovic]-STP-Final Project - Eiffel Tower.std

Hello Everyone For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…

Hello Everyone. I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?

How to create a cantilever slab without beams in the Physical modeler in STAAD connect edition?

Dear sir, As per the attached file when i check the moment diagram for secondary beams 356*171*45 .staad showing as these beams are pinned and in my model,I am considering them as a fixed .Why moment is not coming at the end nodes? roof.std …

How to rectify this failure known as 'Detailing failure' in RCDC

Dear sir, I am doing the analysis of cable but the reactions are coming with an extreme value like 66kn along x. There is no any weight on the cable only self-weight is considered. Kindly explain to me why reactions are so conservative. Also, guide…

How does Moment distribution and release for beams work in STAAD Pro ? While designing Secondary Beams, I’m releasing the moments MX, MY, MZ to a 100% at their ends. if I keep the ends fixed, I get a hogging moment say ‘ X ’ kN-m at the ends. However…

How do I change Mton/Cm to Kn/m