• Templates are too slow

    Hello, Been working on itl files from PW and it takes so long to add end conditions or edit points and components, ORD works just fine it is just the template file.
  • Template: Have Ditch show when slope is toward the roadway

    I recently found an old InRoads video that shows what I am trying to achieve in ORD. I want the ditch to show when the existing grade slopes toward the road and a fill slope when it falls away. The video used the template below. When the slope is below…
  • End Condition Exception: Transition not functioning properly?

    Hello everyone, I'm trying to use an End Exception Transition between two templates. Whenever I place down a transition it has a transition, but in two strokes. See the below images for clarification. Here you can see the transition of the End…
  • Neat solution for trimming earthworks

    I'm trying to get a clean trim between earthworks which are not tangential. The scenario is that I have a footway corridor and on the back of it is a separate earthworks linear template (references the back line in the corridor) because the back of…
  • Targeting a surface twice with an Inroads template

    Good morning / evening / afternoon all, I was wondering if there was a way to have a template target a surface twice when creating a component. I have a project where we're filling in part of a ditch between two embankments, but there's a…
  • End Condition Transition

    I have a corridor where when my end condition linear feature goes from one feature to another it is either creating a gap or dropping the line. This only happens in some areas but not others. Picture 1 is how i want it to function. Picture 2 is my problem…
  • End Condition control_ so much hard to me somebody help me?

    I try to make end condition in blue box. like this. but I dont know hot to make like that(i see that photo in youtube, but he not explain how to make that) 1. how i can make end condition at end of road???(hope to know search word or tutorial!)…
  • Variable end conditions for cut ditches

    I have a corridor template that has both variable fill sections and variable cut sections. The fill works just fine, but the cut does not work fully. When I test the template, it appears to be working, but does not fully display on the cross section explorer…
  • Need Some Help With My Sandstorm (AKA ORD Corridor End Condition Issue)

    Corridors and End Conditions! I have rebuilt my template end conditions 3 times now. Each time the problem gets worse and worse. My end condition is seeking a Horizonal Feature Definition and a Finished Grade Surface. I have a Left and a Right Side. I…
  • End condition exception and linear construction limit both showing.

    My template is set up with priorities to solve for several cut and fill conditions. The guardrail end condition has the highest numerical priority and solved last. Naturally, this creates "pockets" of the guardrail shoulder condition along a corridor…
  • Interface line not connecting

    Hi I've found that I have multiple locations within my corridor where I have gaps in the ground interface line. Any ideas. Background: I have found this happening when going from 1:3 to 1:2 fill (my template has a number of end conditions). I have…
  • A Primary and Secondary End Condition Seek the Same Target, but the Secondary End Condition Does Not Draw

    I am trying to create a template using Openroads that will create a floodplain bench along a stream at a known elevation from the active profile. In the cross-section picture that has been attached, the origin of my template is the green circle. I want…
  • End Condition Targeting a Feature Definition Both Horizontal and Vertical

    I have a template that has an end condition on the left and the right. This particular end condition targets a specific feature definition both horizontally and vertically. The issue is that if I have a targeted feature on only one side of the road, both…
  • Simple Template End Conditions not Working

    I have a very simple driveway template with three end conditions (two for a fill situation and one for a cut situation). When using the template on different driveways, sometime the fill EC works, but not on all of them. The most trouble I am having is…
  • Driveway End Conditions

    I have set up a template for a driveway on a corridor I am working on. The corridor itself has ditches on both sides, and ties to existing terrain. I am looking for the best option when it comes to tieing the end conditions of the driveway into the…
  • End Condition Target Feature XYZ-Dual Solutions

    I have an end condition that I am attempting to have seek a feature XYZ. However, over a particular station range, the feature loops back on itself providing two solutions. Is there a way to have the end condition solve for on over the other without breaking…
  • OpenRoads SS3 End conditions troubleshooting: clear zone testing

    This works: This doesn't: Failure report results: Roadway Designer Results Component Clearzone failed to solve Failed to solve end condition for point 'ES-R-L-R' I'm not sure why both tooltips report the same horizontal and vertical…
  • OpenRoads (Geopak) Corridor Design with Urban Entrances problems

    We are currently having a problem with Driveways and template transitions , mainly in the areas of driveway flares. To give some background, I have tried building this with a civil cell, but I cannot use the temporary measurement tool on this cell in…
  • End Conditions not updating / deleting (GEOPAK SS3 - OpenRoads)

    When I move or delete transitions or template drops in a corridor, the tie-in slopes are remaining. When I extend a different template drop into the area where the deleted template was, there appears to be a conflict (see second screenshot). I've tried…
  • Corridor Modeler Template display - slopes

    When I hover over a ditch, my 4:1 foreslope displays at 25%. So I attempted to adjust by right mouse clicking in the section window of roadway designer, bringing up the "display template" dialog and entered the following, trying to switch it to an alternate…
  • Re: Slope on Template not cooperating

    Keri, Follow Thomas's suggestion to get what you want. Keep in mind that if you have two detached end conditions both looking for existing ground, they will solve together initially. Your 3:1 slope EC doesn't "wait" for the MSE EC to solve, which…
  • End Condition Rounding

    I'm having an issue with EC Rounding. The attached Pdf explains my problem. The blue line represents a normal EC without rounding, defined at a given slope (Say 25%). When I add rounding, the result I get looks something like the Red line. This isn't…
  • Roadway Designer Template Setup..if/then statments

    We are new to Corridor Modeler/Roadway Designer in Geopak and have a few questions how to get things set up correctly. Our first issue is trying to use "if/then" statements on end conditions. Specifically, we want to test the slope between two points…
  • Re: Fixed Slope to advoid ROW issues.

    If your ROW is fairly consistant you could use multiple ECs with priorities based on a horizontal constraint. In the screen shot I have a 1:4 slope to 8' right (8.5' is ROW, my road is centered on the ROW so this works) and if that fails then use a variable…
  • Roadway Designer Target Aliasing

    Perhaps I am trying to use the wrong tool to do this, but I am having an issue trying to get my side slopes to draw correctly. I have a diamond interchange and I am currently modeling the ramps. I have a corridor "complete" for the mailine and the existing…