• Cut/Fill Split for each layerwork component [ORD]

    Hi In ORD 2019 R1, how does one split up the cut and fill quantity reported for a layerwork component? i.e. the amount of material that has to be cut in order to place a component and how much of the component is in fill. Pre-OpenRoads GEOPAK was…
  • OpenRoads Designer: How to calculate volumes of overlapping template drops?

    I am trying to calculate volumes of different layers of asphalt and different layers of groundwork. I've created a template which contains all these layers, where the final groundwork layer is variable (slopes and ramps or not). In my template this layer…
  • Bentley Navigator Measure Volume Issue

    I have an Openroads model that contains an IFC element imported via Aecosim. It looks great in Openroads and Navigator but there is a discrepancy with the volume of the solid being reported. The volume is correct in Openroads. But when I measure it…
  • Is there a way to find the volume between 3 terrain models? Or two terrains below a plane?

    Hello, I need to find the volume between two terrain models but also restricted by a plane elevation (floodplain). Is there a way to accomplish this with PowerGeopak? Thanks! Ben
  • By Open RoadsDesigner, how to separately calculate the earthworks volume?

    Hi, In Open RoadsDesigner, how to separately calculate the earthworks volume? The model has 3 terrains (existing top surface, strong weathering rock layer, and medium weathering rock layer). See the following screenshots: But, in the Component…
  • How to Set up Unsuitable Materials based on Designed Terrain instead of Existing Terrain

    I try to set unsuitable materials referenced to designed terrain model instead of existing terrain in End-Area Volumes. Although I edited settings of unsuitable material's feature from existing terrain to design it is still the same. I would like…
  • Volume from mesh

    I'm trying to figure the volume between two meshes (excavation for bridge pier). I've created one mesh for the excavation limits which extends (upward) to the existing ground surface (meeting the Level: Terrain_Ex_Calc_Triangles_GS), the other mesh is…
  • Pull Volumes from Corridor

    I am attempting to pull quantities from a corridor I have created. The corridor consists of various fills. I am relatively new to InRoads so this may be far more simple than I am making it. The below image shows what I have created.
  • Surface Triangle Volume with Shapes including Holes

    Anyone know if there is a way to use a shape with a hole in it to compute the triangle volume between surfaces? If we need to differentiate cut/fill by areas like this, the only way I can see to do it is use two shapes and then a secondary calculation…
  • Power InRoads Analyse Volume

    Hi, I've been requested to find out the cut volume of an area of the sea bed that is to be cut down to a certain depth with a cut slope of 1:5 and 1:3. Same area location but different slopes. I've created the end-condition template for the slopes,…
  • Using inroads to calculate volume

    I'm pretty sure I've done this before and I simply cannot remember the sequence of doing so. I have a base topo and am overlaying a final fill plan. Wanting to calculate the remaining fill, normally I'll calculate the area of each 5' contour in sq.ft…
  • need to learn how to creat template for cut and fill

    hi every one, I need to learn how to create template from scratch (have used them in past but never created or amend one), the template will be for different cuts and fills, different types of ground condition etc, also to calculate cut and fill volumes…
  • Re: [MX V8i] Volume calculating

    Hello Wolfgang, I have did it other way because I really have little time for experimenting :( I made a little cheat: I have done a two models of section - 1-st from design (which is triangulation model) and 2-nd from subgrade (string model). I got…
  • InRoads V8i: The roadway designer components are not displaying in the cross sections

    It maybe simple, but since I am new to InRoads, I would appreciate your help.... Please see the screen shot below, the road components are not shown on the cross sections. I have tested using different templates, sometimes the components are shown…
  • Reporting a road that has a civil cell

    (Filed for a user) Using as an example a road that has a civil cell at a intersection, how can I integrate the cell within the corridor in order to report the offsets and to get the volume quantity. Thank you, Andrea Garecht
  • gridded volume in PowerCivil for country

    hi, I want to generated grid and show the volumes in the grid, right now we get as a text file! is there a method to create a dgn, with grid and volume of each grid! awaiting reply. regards, vivek
  • Re: [MX V8i] Volume calculating

    Scott, If my way of thinking and understanding is right the temporary section area used to volume calculation between two sections will be determined as on drawing below (between two dotted lines - only in limit where both sections are present one…
  • InRoads V8i SS2: Component Volumes

    I am trying to create a volumes report using end area volumes. When I use Component Quantities from the RoadWay Designer, I can get all components quantities, but when I using End_Area_Volumes from the Cross Sections and used the Volumes as style sheet…