Determining Flood Extents With InRoads 8.5

Elisabeth Pry — Fri, 21 Jun 2013 19:47:20 GMT

Current Revision posted to OpenRoads | OpenSite Wiki by Elisabeth Pry on 6/21/2013 7:47:20 PM


	Applies To

	Product(s):	InRoads 2004 Edtion
	Version(s):	08.05.00.xx
	Environment:	N/A
	Area:	N/A
	Subarea:	N/A
	Original Author:	Bentley Technical Support Group

Overview

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

External Links

Bentley Technical Support KnowledgeBase

Bentley LEARN Server

Comments or Corrections?

Bentley's Technical Support Group requests that you please confine any comments you have on this Wiki entry to this "Comments or Corrections?" section. THANK YOU!

Tags: TechNote, Bentley InRoads 2004 Edition 08050000, Bentley InRoads

Determining Flood Extents With InRoads 8.5

Jacquelyn Pettus — Wed, 13 Feb 2013 20:22:27 GMT

Revision 9 posted to OpenRoads | OpenSite Wiki by Jacquelyn Pettus on 2/13/2013 8:22:27 PM

Document Information

Document Type: TechNote

Product(s): Bentley InRoads 2004 Edtion

Version(s): 08.05.00.xx

Original Author: Bentley Technical Support Group

Legacy Document Number: 8371

Overview

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

External Links

Bentley Technical Support KnowledgeBase

Bentley LEARN Server

Comments or Corrections?

Bentley's Technical Support Group requests that you please confine any comments you have on this Wiki entry to this "Comments or Corrections?" section. THANK YOU!

Tags: Bentley InRoads, Bentley InRoads 2004 Edition 08050000, TechNote

Determining Flood Extents With InRoads 8.5 [TN]

Jacquelyn Pettus — Tue, 06 Nov 2012 20:07:49 GMT

Revision 8 posted to OpenRoads | OpenSite Wiki by Jacquelyn Pettus on 11/6/2012 8:07:49 PM

Document Information

Document Type: TechNote

Product(s): Bentley InRoads 2004 Edtion

Version(s): 08.05.00.xx

Original Author: Bentley Technical Support Group

Legacy Document Number: 8371

Overview

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

External Links

Bentley Technical Support KnowledgeBase

Bentley LEARN Server

Comments or Corrections?

Bentley's Technical Support Group requests that you please confine any comments you have on this Wiki entry to this "Comments or Corrections?" section. THANK YOU!

Tags: Bentley InRoads, Bentley InRoads 2004 Edition 08050000, TechNote

Determining Flood Extents With InRoads 8.5 [TN]

Elisa McGraw — Wed, 21 Jul 2010 21:20:14 GMT

Revision 7 posted to OpenRoads | OpenSite Wiki by Elisa McGraw on 7/21/2010 9:20:14 PM

Document Information

Document Type: TechNote

Product(s): Bentley InRoads 2004 Edtion

Version(s): 08.05.00.xx

Original Author: Bentley Technical Support Group

Legacy Document Number: 8371

Overview

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

External Links

Bentley Technical Support KnowledgeBase

Bentley LEARN Server

Comments or Corrections?

Bentley's Technical Support Group requests that you please confine any comments you have on this Wiki entry to this "Comments or Corrections?" section. THANK YOU!

Tags: Bentley InRoads, Bentley InRoads 2004 Edition 08050000, TechNote

Determining Flood Extents With InRoads 8.5 [TN]

Elisa McGraw — Tue, 22 Jun 2010 13:15:05 GMT

Revision 6 posted to OpenRoads | OpenSite Wiki by Elisa McGraw on 6/22/2010 1:15:05 PM

Document Information

Document Type: TechNote

Product(s): Bentley InRoads 2004 Edtion

Version(s): 08.05.00.xx

Original Author: Bentley Technical Support Group

Legacy Document Number: 8371

Overview

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

External Links

Bentley Technical Support KnowledgeBase

Bentley LEARN Server

Comments or Corrections?

Bentley's Technical Support Group requests that you please confine any comments you have on this Wiki entry to this "Comments or Corrections?" section. THANK YOU!

Tags: Bentley InRoads, Bentley InRoads 2004 Edition 08050000, TechNote

Determining Flood Extents With InRoads 8.5

Elisa McGraw — Tue, 04 Nov 2008 17:23:24 GMT

Revision 5 posted to OpenRoads | OpenSite Wiki by Elisa McGraw on 11/4/2008 5:23:24 PM

Document Information

Document Type: TechNote

Product(s): Bentley InRoads 2004 Edtion

Version(s): 08.05.00.xx

Original Author: Bentley Technical Support Group

Legacy Document Number: 8371

Overview

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

External Links

Bentley Technical Support KnowledgeBase

Bentley LEARN Server

Comments or Corrections?

Bentley's Technical Support Group requests that you please confine any comments you have on this Wiki entry to this "Comments or Corrections?" section. THANK YOU!

Tags: Bentley InRoads, Bentley InRoads 2004 Edition 08050000, TechNote

Determining Flood Extents With InRoads 8.5

Elisa McGraw — Thu, 30 Oct 2008 14:32:01 GMT

Revision 4 posted to OpenRoads | OpenSite Wiki by Elisa McGraw on 10/30/2008 2:32:01 PM

Document Information

Document Type: TechNote

Product(s): Bentley InRoads 2004 Edtion

Version(s): 08.05.00.xx

Original Author: Bentley Technical Support Group

Overview

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

External Links

Bentley Technical Support KnowledgeBase

Bentley LEARN Server

Comments or Corrections?

Bentley's Technical Support Group requests that you please confine any comments you have on this Wiki entry to this "Comments or Corrections?" section. THANK YOU!

Tags:

Determining Flood Extents With InRoads 8.5

Elisa McGraw — Tue, 21 Oct 2008 20:25:22 GMT

Revision 3 posted to OpenRoads | OpenSite Wiki by Elisa McGraw on 10/21/2008 8:25:22 PM

Document Information

Document Type: TechNote

Product(s): Bentley InRoads 2004 Edtion

Version(s): 08.05.00.xx

Original Author: Bentley Technical Support Group

Overview

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

External Links

Bentley Technical Support KnowledgeBase

Bentley LEARN Server

Comments or Corrections?

Bentley's Technical Support Group requests that you please confine any comments you have on this Wiki entry to this "Comments or Corrections?" section. THANK YOU!

Tags:

Determining Flood Extents With InRoads 8.5

Elisa McGraw — Tue, 21 Oct 2008 20:03:06 GMT

Revision 2 posted to OpenRoads | OpenSite Wiki by Elisa McGraw on 10/21/2008 8:03:06 PM

Document Information

Document Type: TechNote

Product(s): Bentley InRoads 2004 Edtion

Version(s): 08.05.00.xx

Original Author: Bentley Technical Support Group

Overview

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

External Links

Bentley Technical Support KnowledgeBase

Bentley LEARN Server

Comments or Corrections?

Bentley's Technical Support Group requests that you please confine any comments you have on this Wiki entry to this "Comments or Corrections?" section. THANK YOU!

Tags:

Determining Flood Extents With InRoads 8.5

Hannah Blye — Mon, 30 Jun 2008 13:00:01 GMT

Revision 1 posted to OpenRoads | OpenSite Wiki by Hannah Blye on 6/30/2008 1:00:01 PM

Product:	Bentley InRoads 2004 Edtion v08.05.00.xx
Date Added:	June 30, 2008

When working with an existing river basin DTM, the following workflow should depict the location where the 20 foot flood level will intercept with the original surface:

Place linestrings along each bank of the river.
Create features in the surface from the linestrings:
1. Select File > Import > Surface - From Graphics
2. Select Drape to Surface.
3. Select Exclude from Triangulation.
Move the features up 20 feet in elevation:
1. Select Surface > Edit Surface > Transform Surface.
2. Set Method to Relative.
3. Set Elevation to 20.
4. Original and Destination surfaces are the same.
Display the features in the design file.
1. Select Surface > View Surface > Features.
2. Select the two features created in Step 2.
Create a Decision Table that moves horizontally to intercept the surface.
1. Create a single entry in the decision table that has a 0% slope and extends far enough horizontally so that it will intercept with the surface.
2. Toggle on Seek Intersection and Construct Point.
Select Surface > Design Surface > Apply Decision Table to run the horizontal decision table along the features created in Step 2.
1. Add the intercept into the surface or select Generate Graphics Only.

Option: Instead of creating two features for the river banks, use a horizontal alignment along the river to create a single feature. Then apply the decision table off both sides.

Tags:

Determining Flood Extents With InRoads 8.5

Determining Flood Extents With InRoads 8.5

Overview

See Also

External Links

Comments or Corrections?

Determining Flood Extents With InRoads 8.5

Document Information

Overview

See Also

External Links

Comments or Corrections?

Determining Flood Extents With InRoads 8.5 [TN]

Document Information

Overview

See Also

External Links

Comments or Corrections?

Determining Flood Extents With InRoads 8.5 [TN]

Document Information

Overview

See Also

External Links

Comments or Corrections?

Determining Flood Extents With InRoads 8.5 [TN]

Document Information

Overview

See Also

External Links

Comments or Corrections?

Determining Flood Extents With InRoads 8.5

Document Information

Overview

See Also

External Links

Comments or Corrections?

Determining Flood Extents With InRoads 8.5

Document Information

Overview

See Also

External Links

Comments or Corrections?

Determining Flood Extents With InRoads 8.5

Document Information

Overview

See Also

External Links

Comments or Corrections?

Determining Flood Extents With InRoads 8.5

Document Information

Overview

See Also

External Links

Comments or Corrections?

Determining Flood Extents With InRoads 8.5