Cut and Fill Values and Graphics do not display when running the Open Cross Section View command

Jacquelyn Pettus — Mon, 03 Nov 2014 17:48:20 GMT

Current Revision posted to OpenRoads | OpenSite Wiki by Jacquelyn Pettus on 11/3/2014 5:48:20 PM

Product(s):	InRoads
Version(s):	08.11.09+
Area:	Cross Section
Original Author:	Kevin McDonald, Bentley Technical Support Group

Problem:

I cut dynamic sections using the Open CrossSection Views command, and when I select View Properties to turn on Display Cut and Fill Graphics or Display Cut and Fill Values, they do not display

Solution:

There are 2 things that will allow the cut/fill graphics and cut/fill values to show up in the cross section views:

1.) Verify the existing ground is set as the Active terrain

2.) Run the Process Corridor command before creating the sections.

Tags: Cut and Fill Graphics, Open CrossSection View, corridor modeling

Cut and Fill Values and Graphics do not display when running the Open Cross Section View command

Jacquelyn Pettus — Mon, 03 Nov 2014 17:48:03 GMT

Revision 7 posted to OpenRoads | OpenSite Wiki by Jacquelyn Pettus on 11/3/2014 5:48:03 PM

Product(s):	InRoads
Version(s):	08.11.09+
Area:	Cross Section
Original Author:	Kevin McDonald, Bentley Technical Support Group

Problem:

I cut dynamic sections using the Open CrossSection Views command, and when I select View Properties to turn on Display Cut and Fill Graphics or Display Cut and Fill Values, they do not display

Solution:

There are 2 things that will allow the cut/fill graphics and cut/fill
values to show up in the cross section views:

1.) Verify the existing ground is set as the Active terrain

2.) Run the Process Corridor command before creating the sections.

Tags: Cut and Fill Graphics, Open CrossSection View, corridor modeling

Cut and Fill Values and Graphics do not display when running the Open CrossSection View command

Beebe Ray — Thu, 17 Jul 2014 17:22:24 GMT

Revision 6 posted to OpenRoads | OpenSite Wiki by Beebe Ray on 7/17/2014 5:22:24 PM


	Applies To

	Product(s):	InRoads
	Version(s):	08.11.09.493
	Environment:	N/A
	Area:	Corridor Modeling
	Subarea:
	Original Author:	Kevin McDonald, Bentley Technical Support Group

Problem:

I cut dynamic sections using the Open CrossSection Views command, and when I select View Properties to turn on Display Cut and Fill Graphics or Display Cut and Fill Values, they do not display

Solution:

There are 2 things that will allow the cut/fill graphics and cut/fill
values to show up in the cross section views:

1.) Verify the existing ground is set as the Active terrain

2.) Run the Process Corridor command before creating the sections.

Tags: Cut and Fill Graphics, Open CrossSection View, corridor modeling

Cut and Fill Values and Graphics do not display when running the Open CrossSection View command

Kevin McDonald — Tue, 30 Jul 2013 19:13:13 GMT

Revision 5 posted to OpenRoads | OpenSite Wiki by Kevin McDonald on 7/30/2013 7:13:13 PM


	Applies To

	Product(s):	InRoads
	Version(s):	08.11.09.493
	Environment:	N/A
	Area:	Corridor Modeling
	Subarea:
	Original Author:	Kevin McDonald, Bentley Technical Support Group

Problem:

I cut dynamic sections using the Open CrossSection Views command, and when I select View Properties to turn on Display Cut and Fill Graphics or Display Cut and Fill Values, they do not display

Solution:

There are 2 things that will allow the cut/fill graphics and cut/fill
values to show up in the cross section views:

1.) Verify the existing ground is set as the Active terrain

2.) Run the Process Corridor command before creating the sections.

Tags: Cut and Fill Graphics, Open CrossSection View, corridor modeling

Cut and Fill Values and Graphics do not display when running the Open CrossSection View command

Kevin McDonald — Tue, 30 Jul 2013 19:12:58 GMT

Revision 4 posted to OpenRoads | OpenSite Wiki by Kevin McDonald on 7/30/2013 7:12:58 PM


	Applies To

	Product(s):	InRoads
	Version(s):	08.11.09.493
	Environment:	N/A
	Area:	Corridor Modeling
	Subarea:
	Original Author:	Kevin McDonald, Bentley Technical Support Group

Problem:

I cut dynamic sections using the Open CrossSection Views command, and when I select View Properties to turn on Display Cut and Fill Graphics or Display Cut and Fill Values, they do not display

Solution:

There are 2 things that will allow the cut/fill graphics and cut/fill
values to show up in the cross section views:

1.) Verify the existing ground is set as the Active terrain

2.) Run the Process Corridor command before creating the sections.

Tags: Corridor Modeling, Open CrossSection View, Cut and Fill Graphics

Cut and Fill Values and Graphics do not display when running the Open CrossSection View command

Kevin McDonald — Tue, 30 Jul 2013 19:12:43 GMT

Revision 3 posted to OpenRoads | OpenSite Wiki by Kevin McDonald on 7/30/2013 7:12:43 PM


	Applies To

	Product(s):	InRoads
	Version(s):	08.11.09.493
	Environment:	N/A
	Area:	Corridor Modeling
	Subarea:
	Original Author:	Kevin McDonald, Bentley Technical Support Group

Problem:

I cut dynamic sections using the Open CrossSection Views command, and when I select View Properties to turn on Display Cut and Fill Graphics or Display Cut and Fill Values, they do not display

Solution:

There are 2 things that will allow the cut/fill graphics and cut/fill
values to show up in the cross section views:

1.) Verify the existing ground is set as the Active terrain

2.) Run the Process Corridor command before creating the sections.

Tags: Corridor Modeling, Open CrossSection View, Cut and Fill Graphics

Cut and Fill Values and Graphics do not display when running the Open CrossSection View command

Kevin McDonald — Tue, 30 Jul 2013 19:11:30 GMT

Revision 2 posted to OpenRoads | OpenSite Wiki by Kevin McDonald on 7/30/2013 7:11:30 PM


	Applies To

	Product(s):	InRoads
	Version(s):	08.11.09.493
	Environment:	N/A
	Area:	Corridor Modeling
	Subarea:
	Original Author:	Kevin McDonald, Bentley Technical Support Group

Problem:

I cut dynamic sections using the Open CrossSection Views command, and when I select View Properties to turn on Display Cut and Fill Graphics or Display Cut and Fill Values, they do not display

Solution:

There are 2 things that will allow the cut/fill graphics and cut/fill
values to show up in the cross section views:

1.) Verify the existing ground is set as the Active terrain

2.) Run the Process Corridor command before creating the sections.

Tags: Corridor Modeling, Open CrossSection View, Cut and Fill Graphics

Cut and Fill Values and Graphics do not display when running the Open CrossSection View command

Kevin McDonald — Tue, 30 Jul 2013 19:10:21 GMT

Revision 1 posted to OpenRoads | OpenSite Wiki by Kevin McDonald on 7/30/2013 7:10:21 PM


	Applies To

	Product(s):	InRoads
	Version(s):	08.11.09.493
	Environment:	N/A
	Area:	Corridor Modeling
	Subarea:
	Original Author:	Kevin McDonald, Bentley Technical Support Group

Problem:

I cut dynamic sections using the Open CrossSection Views command, and when I select View Properties to turn on Display Cut and Fill Graphics or Display Cut and Fill Values, they do not display

Solution:

There are 2 things that will allow the cut/fill graphics and cut/fill
values to show up in the cross section views:

1.) Verify the existing ground is set as the Active terrain

2.) Run the Process Corridor command before creating the sections.

Tags: Corridor Modeling, Open CrossSection View, Cut and Fill Graphics