Single Offset Entire Element command does not offset correctly

Jacquelyn Pettus — Fri, 17 Oct 2014 18:02:29 GMT

Current Revision posted to OpenRoads | OpenSite Wiki by Jacquelyn Pettus on 10/17/2014 6:02:29 PM

Product(s):	InRoads, MX, GEOPAK
Version(s):	08.11.09+
Area:	Horizontal Geometry
Original Author:	Andrea Garecht, Bentley Technical Support Group

Problem:

When running the command Single Offset Entire Element on a Complex Alignment, it does not always offset properly. Some elements are offset to the right while the others are to the left. See picture below for example.

The green line in this picture is the Offset alignment.

Explanation:

It appears in this situation, the alignment was complexed incorrectly.

Solution:

Run the Remove Rules command under General Geometry
Recreate the Rule with the Complex By Element command.
Verify that the arrows are pointing in the correct direction when selecting the elements: Notice the arrow is pointing in the opposite direction. In this example, the arrow is pointing in the proper direction.
Rerun the Single Offset Entire Element command and the results should appear correct.

Tags: InRoads, Geometry, SELECTsupport, Problem Solving

Single Offset Entire Element command does not offset correctly

Jacquelyn Pettus — Wed, 23 Jul 2014 20:57:37 GMT

Revision 3 posted to OpenRoads | OpenSite Wiki by Jacquelyn Pettus on 7/23/2014 8:57:37 PM


	Applies To

	Product(s):	InRoads
	Version(s):	08.11.09.493
	Environment:	N/A
	Area:	Geometry
	Subarea:
	Original Author:	Andrea Garecht, Bentley Technical Support Group

Problem Description

The green line in this picture is the Offset alignment.

Reason

It appears in this situation, the alignment was complexed incorrectly.

Steps to Resolve

Run the Remove Rules command under General Geometry
Recreate the Rule with the Complex By Element command.
Verify that the arrows are pointing in the correct direction when selecting the elements: Notice the arrow is pointing in the opposite direction. In this example, the arrow is pointing in the proper direction.
Rerun the Single Offset Entire Element command and the results should appear correct.

Tags: InRoads, Geometry, SELECTsupport, Problem Solving

Single Offset Entire Element command does not offset correctly

Beebe Ray — Thu, 17 Jul 2014 18:18:33 GMT

Revision 2 posted to OpenRoads | OpenSite Wiki by Beebe Ray on 7/17/2014 6:18:33 PM


	Applies To

	Product(s):	InRoads
	Version(s):	08.11.09.493
	Environment:	N/A
	Area:	Geometry
	Subarea:
	Original Author:	Andrea Garecht, Bentley Technical Support Group

Problem Description

The green line in this picture is the Offset alignment.

Reason

It appears in this situation, the alignment was complexed incorrectly.

Steps to Resolve

Run the Remove Rules command under General Geometry
Recreate the Rule with the Complex By Element command.
Verify that the arrows are pointing in the correct direction when selecting the elements: Notice the arrow is pointing in the opposite direction. In this example, the arrow is pointing in the proper direction.
Rerun the Single Offset Entire Element command and the results should appear correct.

Tags: InRoads, Geometry, SELECTsupport, Problem Solving

Single Offset Entire Element command does not offset correctly

Andrea Garecht — Thu, 15 Aug 2013 21:03:44 GMT

Revision 1 posted to OpenRoads | OpenSite Wiki by Andrea Garecht on 8/15/2013 9:03:44 PM


	Applies To

	Product(s):	InRoads
	Version(s):	08.11.09.493
	Environment:	N/A
	Area:	Geometry
	Subarea:
	Original Author:	Andrea Garecht, Bentley Technical Support Group

Problem Description

The green line in this picture is the Offset alignment.

Reason

It appears in this situation, the alignment was complexed incorrectly.

Steps to Resolve

Run the Remove Rules command under General Geometry
Recreate the Rule with the Complex By Element command.
Verify that the arrows are pointing in the correct direction when selecting the elements: Notice the arrow is pointing in the opposite direction. In this example, the arrow is pointing in the proper direction.
Rerun the Single Offset Entire Element command and the results should appear correct.

Tags: InRoads, Geometry, SELECTsupport, Problem Solving