Browse By Tags

  • Cross Section Annotation For Every 5m or 10 m or for a Paticular Distance

    Dear All Thankfull for Responding my Questons I Have a Another Doubt and Problem, i am Creating cross sections in BRT it is coming good, When I am Annotating the Cross sections the offset and eelevations are showing at ground change points only…

  • PROFILE RAIL ELEVATION

    Dear All, I am facing a problem with rail elevation this is most importent for me to show rail elevation in the profile, our railways did'nt accept with out rail elevations, for rail elevation again i am going to auto cad. I am creating a horizontal…

  • stripping

    I used stripping under fill when draw a rail template. When I calculate wolumes In the template apears two area numbers A1 ,A2(msq) ,one without and one with stripping. But the calculaton on the volume fill between two templates is not corect. It is much…

  • Cross Section Component Display Problems

    Hi, Using InRoads 8.08.00.46 and trying to generate cross sections. The problem is that some of the components are not displaying properly. For example, I have my Left lane component sloping the opposite direction in the cross sections or 2 curbs at different…

  • Driveways in Cross Sections

    I am trying to create cross sections for a few various size corridors. I started with the simplest/shortest corridors. I have a template that is controlled by parametric constraints as to what object (curb and gutter, ditches, etc.) will appear. One of…

  • Staking Reports-Inroads

    I am trying to produce a "staking report" for a roadway design. In the staking report I need to include elevations and offsets for centerline and my grade breaks in my template. In the cross section report box you can select a surface and "include selected…

  • Cross Section: proposed surface/end condition doesn't intercept existing ground

    I am using Inroads Suite XM Edition. When I create my cross sections I notice that my proposed surface, in many cases, does not actually meet the existing ground surface like it should. In roadway modeler, the section views all look correct, but in the…

  • Re: Cross Section Component Display Problems

    Sounds like maybe your proposed dtm was not emptied prior generating your surface again from the Roadway designer. If it wasn't emptied, it could leave components from previous iterations in the dtm which could explain the multiple components showing…

  • Re: Annotate Storm and Sanitary in Cross Section

    Marc, Go to Drafting> Place Cross Section Note. In the bottom, right hand corner of the dialog, click the black arrow to expand the dialog. Under Inserts, you should see Storm and Sanitary Structures. Add the desired inserts to a new or existing…

  • Re: Inroads XM: Cross section surface extends off the top of window

    Tim, Do you have 'Show Data Outside Elevation Range' toggled on the General leaf of the Create Cross Section dialog? If so, toggle that off. Thanks, Jason Smithey

  • Re: InRoads XM - Annotate Cross Section Offsets

    I'm not sure what you are expecting the Offset Tolerance to do for you but the point that you feel should be annotated is closer than 0.1m as best I can tell from the figures. Offset Tolerance is meant to remove that point from being annotated. …

  • Re: Driveways in Cross Sections

    I had tried that in the past and didn't have much better luck but will give it a try. I wonder though what the best way to get the driveway across its entire length to match into existing with a reasonable slope and length. I have in the past picked the…

  • Re: Inroads Update Cross Section Notes

    Ryan, I have reproduced your problem and filed D-37693. Thanks for reporting this. Jason Smithey

  • Re: Inroads - Volumes from Custom X-sections

    Greetings- You say you have "custom cross sections". How were these customized? Typically, if one needs to tweak any cross sections that InRoads has produced, one is restricted to only three MicroStation tools: Modify element Insert…

  • Re: Custom Cross-Section Set

    On the General leaf, enter a number larger than the span of your alignment for the interval. I sometimes just enter 1,000,000. On the Controls> Critical Sections leaf, turn off all of the options that you do not want. See the help file for an explanation…

  • InRoads Cross Section tools

    Using both InRoads 8.5SP7 or 8.9SP? I would like to add flow arrows to the cross sections? Suggestions? In the past I created a feature and displayed the arrow as a cell but I was never able to figure out how to make the cell be…

  • End Area Volumes in Cross Sections

    I have 2 sets of cross sections recently where I needed to get volumes from my cross sections that are cut at 50' intervals. Ocassionally I have had to hand end the cross sections to change a particular cut or fill or if for some reason the components…

  • IR - Intersections and Volumes

    Designing intersections in the roadway designer with the use of secondary alignments for the curb returns works WONDERFULLY... Until I have to run volumes. To mimic the secondary alignments in cross section, I currently use custom linestrings…

  • Please help me with this template.

    Ok here is the deal. I have a road that was originally designed to be a 4 lane parkway. Only half of it was built years ago and now part of it needs repaired and part is just getting the additional lanes and median added. Naturally I'm trying to do this…
    • Parkway.itl

  • Re: Profiles

    Charles, Please see the following posting: http://communities.bentley.com/Products/Road___Site_Design/f/5922/t/22389.aspx Thanks, Jason Smithey

  • Inroads Cross Section Report Question

    Hi everyone, When running a cross section report with multiple surfaces, what determines the order in which the surfaces are called from inroads into the report? I'd like to be able to manage this order before calling the report so I'm not moving…

  • Re: Inroads - Volumes from Custom X-sections

    End area volumes are not computed on skewed cross sections. Thanks, Jason Smithey

  • Adding Sheet Number to Cross Section

    I have been trying to have Inroads xm 8.9 to display sheet number in my cross section. I have tried with a border inserted as a cell and as reference. Any help would be appreciated. Thanks

  • Re: InRoads. X-sections anotation problem

    Corey, The problems that I noted should only be in V8i. If you are having problems then you may want to contact support with your dataset. Also, it may not fix your collision free text problem but you should upgrade to version 08.09.03…

  • Missing Segments When Displaying Cross Sections With Inroads 8.9

    I am having a problem using Inroads version 08.09.02.16. When I display cross sections in Microsation XM using this Inroads version, I tend to have lines missing in the finished cross sections. These missing segments are displayed in the roadway designer…
Communities
Support and Services
Training and Learning
Social Media