Browse By Tags

Hi If we define bar length, is leap bridge software have capability to deduct development length based on dia of bar and calculate flexure check at that point.

I need to change the stress limits for the bent cap from normal exposure (=0.19 sqrt(fc) <0.6ksi ) to severe exposure (=0.0948 sqrt (fc)<0.3ksi)

When running analysis with and without P-delta I noticed there is a substantial increase in the axial column force when P-delta is applied. At the node 1 the difference is about 300 kips. What could be a reason for such an increase? Any insight is appreciated…

Hello - I am modeling hammerhead piers in RC-Pier Version 20.00.00.58. EQ/ES/LS loads are applied at the bottom of the column with a user-defined seismic load combination. For some piers, the seismic shear output at the top of the column shows Combo …

My version of Leap Bridge Concrete currently allows for the use of STM in hammerhead pier caps, but we also need that option for all cap types in multi-column bents. We also need an STM option for prestressed and CIP concrete girders in Leap Bridge Concrete…

I have bent that is being constructed in two phases so some shrinkage will happen on the first phase before the next phase is constructed. In the final condition, I could assume the entire shrinkage strain is applied to both sections but that will be…

Hi. My hand calculations show that my concrete column will go into tension for my earthquake loading, but the my LEAP Concrete Diagram for the column doesn't show anything for the interaction diagram for a column in tension. Is there a check box that…

Hello. I'm wondering how LEAP Version 21.01.00.22 calculates the maximum axial load displayed in the diagram. The diagram displays a maximum axial force allowed of 1802 kips. As expected the 1802 kips doesn't change regardless of the load combination…

Does RC Pier check shear friction in the pier cap (AASHTO 5.7.4)? I've looked in the output reports and didn't see reference to this spec section. I've also looked in the application help interface and couldn't find it. Note: my application version…

Hello, I have 95 ft long and 12 ft wide abutment footing on 2 rows of piles. Abut stem is 88 ft long. How is the Leap program calculating Dist (ft) , dv, Vu and Phi Vc for X and Z ? I will appreciate the response. Thanks,

Hello, This is an issue that I have seen with previous versions and still has not been resolved. When the need for different material properties and other design parameters is different from the generalized materials tab parameters, the use of the…

Hello, Is LEAP Bridge concrete / RC-Pier capable of having a structure simple span for dead load and continuous for live load (SDCL)? Thanks.

Hello, I am designing the shear reinforcement in a straight pier cap for a multi-column pier. The issue I am having is that whenever I increase the number of legs for my stirrups, the area of steel required also increases to the point where increasing…

Hi, There are cases where centrifugal forces produce a moment that actually counteracts the critical moment in the column, does RCPier consider effects due to vehicle cases without centrifugal forces as provisioned in AASHTO Spec (See below excerpt…

Hello, I have been experiencing a substantial amount of instability/crashing in LBC 20.00.00.46. The program will randomly freeze and become unresponsive. This happens when I run an analysis, look things up in the help manual, attempt to save, and many…

When checking Show P-delta Effects in the Analysis tab, are the values shown represent values with p-delta effect? For example, are the column/shaft moments magnified with p-delta factor in these load combinations (with a "C" on the end of the LC#)? If…

There is an A/D Parameter, under the "Footing" tab to consider effective footing dimensions in analysis of a spread footing. This appears to calculate the effective footing assuming the footing is bearing on soil (as opposed to rock). Is there a way to…

I am using Leap Concrete Version 18.02.02.03 for a multi column pier design that includes seismic forces. I need to apply a response modification factor for the columns and the help guide states that this can be modified in the Seismic Parameters. However…

Hi All I am modelling and designing multi column pier in Leap, But after applying loads i am getting ambiguous bending moment, also huge reinforcement is showing on designing. Please find the model attached and any one please can help and check the…

I am designing a hammerhead pier using the substructure module in LEAP Bridge Concrete. The geometry is a little odd...it's a hammerhead cap on a circular column. To compare the results for the cap design from the conventional sectional design & strut…

I am using Leap Bridge Concrete to design a skewed wall pier. After analyzing the pier, I noticed that for the braking force, that the sum of the forces in the z-direction at the top of the wall did not equal the sum of the forces in the z-direction at…

I am designing a 2-span precast prestressed beam bridge in LEAP Bridge Concrete CONNECT Edition v17.00.01.01. The bearing dimensions along the pier cap are shown correctly in the following view under the 'Substructure' tab: However, when you click…

How does RC Pier (LEAP SubStructure) account for skew when calculating the bearing reactions for the Auto Generated Live Loads. I can replicate the reactions when there is no skew, but I have issues when skew is applied. Any assistance on the matter would…

I am using the LEAP Bridge Substructure module to design a pier for a continuous 4 span structure using HS20 LFD loads. In the AASHTO Standard Specifications, it gives you a few options for the loading. One is that you can use a lane load with one concentrated…