Browse By Tags

  • Error when generating the mesh for embedded beams set to grout body

    Application PLAXIS 3D Issue status Solved First Affected Version PLAXIS 3D 2023.2 Found in Version PLAXIS 3D 2023.2 Fixed and Released in Version PLAXIS 2D 2023.2.1 Issue # 1268947 Date created 31 August…

  • Excess pore water pressure is non-zero at the soil-drain interface

    I installed a PVD (line drain) on MCC soil model and completed a consolidation analysis. In the output, the excess pore pressure at the drain is non-zero. I have used very fine mesh for this study, taking the smallest element as possible. How can I make…

  • Picos [204] incorrect solution, slow convergence when boundary and flow conditions are changed in PVD installed soil

    I wanted to create a graph of excess pore pressure vs radial/horizontal distance for an MCC soil model at a particular depth installed with prefabricated vertical drains. To simulate the effect of smear, transition and undisturbed zones around the PVD…

  • An error occurred in the application – What to do

    Application PLAXIS 2D PLAXIS 3D Version PLAXIS 2D CONNECT Edition PLAXIS 3D CONNECT Edition Date created 17 November 2022 Date modified 17 November 2022 Original author Stefanos Papavasileiou - Bentley Technical Support…

  • PLAXIS 3D MESHING ERROR

    Hi, I have tried meshing a model in PLAXIS 3D and the error is as follows Meshing failed with the following error: Fatal: Could not generate mesh. Warning: 351 EMR warnings have been detected. The 15 most severe are listed, the remaining 336 are not…

  • PLAXIS 3D MESH WARNING

    Hi, I tried generating mesh for a project in PLAXIS 3D and got the following error. Meshing failed with the following error: Fatal: Could not generate mesh. Warning: 351 EMR warnings have been detected. The 15 most severe are listed, the remaining…

  • PLAXIS 3D - 'Information - please wait a moment' and programme crashing when trying to calculate

    When I try to calculate my PLAXIS 3D model, the programme stalls with a pop up saying 'Information - please wait a moment', then I get the below error message . The model doesn't even start to calculate. I've tried saving it in different locations and…

  • Error code:111 in modelling of a NATM Tunnel in PLAXIS 3D

    Dear Soilvision Forum, I'm currently working on my diploma thesis and I'm modelling compensation grouting above a NATM tunnel. The tunnel is only a part of the thesis to cause settlements for the compensation grouting. After a preheaving phase the…

  • Plaxis 3D Save failure?

    Hi guys, Getting a failure when trying to save *any* of my projects, even when opening and immediately trying to save over old, completed projects. I've tried moving the project file and folder to new, "shorter" locations, removing the data.convd…

  • Can't Regenerate the Mesh with Polycurve Surface

    Hello Plaxis team, I have been facing the trouble about regenerate the Mesh. In my case, I want to make a surface by connecting polycurves (Image below). But when I'm trying to regenerate the mesh and change the coarseness factor, It didn't work and show…

  • MESHING FAILED

    Hi guys... Im facing this error while meshing my model on PLAXIS 3D?? Could anyone help me?? Thanks in advance 0156> _gotomesh OK !!!!> _mesh 0.05 30 15 256 Meshing failed with the following error: Meshing failed. Check your model for inaccurately…

  • PLAXIS 3D Meshing Fails

    Generally we have problem with the meshing module in PLAXIS 3D. The only time that we get a successful meshing of the program is where the project is made of horizontal/vertical lines/surfaces. Otherwise, majority of inclined/curved/irregular surfaces…

  • NaN found in stiffness matrix element. [Error code: 36]

    I am getting this message in my 5th calculation phase. the phase was running OK before i did some changes in the model. No clue about the error or problem area.

  • Embedded Pile with Error Code: 204

    Hi everyone, I am trying to run 3D model but no success. In the first step, I'm using the Mohr-Coulomb model and the modulus young in soil parameter has large different parameters from 15k until 4 mil. And I gradually change it but still shows the same…

  • Error Code 204 during remote scripting

    Hi all! I'm currently working on remote skripping a model for optimizing the geometry of a geofoam in-filled trench for vibration reduction at high-rise buildings during pile driving works. I therefore wrote a code to change a various amount of possible…

  • PLAXIS 3D 2018 may not always properly load a model after intersection issues

    Application PLAXIS 3D Issue status ✔ Solved First Affected Version PLAXIS 3D 2018.00 Found in Version PLAXIS 3D 2018.00 Fixed and Released in Version PLAXIS 3D CONNECT Edition V20 Issue # SW-35334 …

  • Accidental inaccurate results in PLAXIS 3D with large incremental multiplier Mstage

    Application PLAXIS 3D Issue status ✔ Solved First Affected Version PLAXIS 3D 2010 Found in Version PLAXIS 3D 2010 Fixed and Released in Version PLAXIS 3D 2013.00 Issue # 15783 Date created 23 September…

  • Error when generating 3D mesh

    Application PLAXIS 3D Version PLAXIS 3D Date created 30 May 2011 Date modified 01 November 2019 Date modified 01 November 2019 Applications PLAXIS 3D Problem description My mesh fails with a certain error…
Communities
Support and Services
Training and Learning
Social Media