Browse By Tags

  • non linear Cable analysis

    Hi, Can u explain anyone What is the meaning of REFORM 1 KGEOM 1 in non linear cable analysis what if i keep 0 instead of 1 " REFORM 1 KGEOM 0" Thanks in advance
  • STAAD's Displacement

    Is this a normal displacement in STAAD.Pro Connect Edition? I am designing a pedestrian footbridge and I happened to encounter this displacement in a certain load case?
  • hi everyone, can anybody help me to solve this model because have error of the snow and seismic loads??

    STAAD SPACE START JOB INFORMATION ENGINEER DATE 30-Nov-22 END JOB INFORMATION INPUT WIDTH 79 UNIT MMS KN JOINT COORDINATES 55 468.544 16072.7 192.577; 73 507.061 16072.7 -1.061; 107 358.857 16072.7 356.735; 151 7030.99 14763.7 2911.01; 152 7609.76 14763…
  • STAAD ANALYSIS

    Hi Everyone! I'm having a hard time fixing my model. it has a warning saying WARNING-fx fy fz wind forces: I Can't correct it no matter what i do. Can Anyone help me out? Thanks a lot always. Here is the file 5488.FILE.std
  • Staad.Pro - Seismic loads by response spectra

    Hi, I need help defining seismic loads by using the response spectra line graph. I add seismic periods and accelerations in the 'Load Case Details' section (attached image). I did not use the 'Definitions' section to consider seismic. My question is how…
  • Why I cant get to see beam and column design report and reinforcement detail on run analysis?

    Please go through the file and reply ASAP. I am waiting.Please go through the file and reply ASAP. I am waiting. sabbir ahmed -static.std
  • *** ERROR : "DEFINE" COMMANDS FOR LOAD GENERATION SHOULD BE PROVIDED BEFORE SPECIFYING PRIMARY LOAD CASES.

    Hi, Hopefully, you are doing well. could you please help me to solve this error? this is the code below. regards, DEFINE WIND LOAD TYPE 1 WIND -Z (WINDWARD WALL) <! STAAD PRO GENERATED DATA DO NOT MODIFY !!! ASCE-7-2010:PARAMS 137.000 KMPH 0…
  • RE: Buckling Analysis and Effective length

    Dear Team I am working with the Staad model for buckling analysis . The buckling load factor is given by the staad after the analysis , wanted to understand the how to manually check the Buckling load factor using Critical Euler equation . I have manually…
  • base shear and lateral displacement value not matching with etab model

    Dear sir, Base shear gets by staad model is coming 269KN which is not matching with etab model (base shear 500kn) prepared by consultant.Also lateral displacement on siesmic cases is more in etab model than staad model.Can you explain why staad model…
  • *WARNING- ZERO STIFFNESS IN DIRECTION 1 AT JOINT 11 EQN. NO. 1 LOADS APPLIED OR DISTRIBUTED HERE FROM ELEMENTS WILL BE IGNORED. THIS MAY BE DUE TO ALL MEMBERS AT THIS JOINT BEING RELEASED OR EFFECTIVELY RELEASED IN THIS DIRECTION. and several other w...

    Good day Everyone! I have several warnings in what I'm trying to design. I designed this model in STAAD TRUSS since this is a truss. Below are the details. Thanks in advance. P R O B L E M S T A T I S T I C S -----------------------------…
  • Wind lateral force is not showing in many nodes though I have provided data. Why?

    1st link /cfs-file/__key/communityserver-discussions-components-files/5932/2251.Dhrubojyoti-Ghosh-JU-Project-_2D00_-Copy-_2800_2_2900_.std 2nd link
  • Member Design Failed

    Dear Members, Please help me to resolve the error for Beam no 55,142 Error - Nominal shear force exceeds tauc_max limit I already tried by increasing the Grade of concrete, increase cross-section size, increase min and max dia of main and sec reinforcement…
  • Design of Solid slab (Conventional slabs)

    Hello Everyone For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…
  • Dummy beam

    Hello Everyone. I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?
  • moment diagram

    Dear sir, As per the attached file when i check the moment diagram for secondary beams 356*171*45 .staad showing as these beams are pinned and in my model,I am considering them as a fixed .Why moment is not coming at the end nodes? roof.std …
  • RCDC Detailing Failure

    How to rectify this failure known as 'Detailing failure' in RCDC
  • MOMENT DISTRIBUTION IN STAAD Pro FOR PARTIALLY RELEASED BEAMS

    How does Moment distribution and release for beams work in STAAD Pro ? While designing Secondary Beams, I’m generally releasing the moments MX, MY, MZ to a 100% at their ends. If I keep the ends fixed, I get a hogging moment say ‘ X ’ kN-m at the…
  • Mton/Cm to Kn/m

    How do I change Mton/Cm to Kn/m
  • Gantry crane moving load along Z axis

    Dear All, Currently i'm designing a gantry crane. 1. I have assigned the loading from Crab to the gantry beam as moving load (Shows in Red color), But i have no idea how to assign the loading (Shows in Green color) when gantry crane is moving along…
  • UC Ratio problem

    warehouse.zip wind calculation also in that folder.... try to fix this probem guys
  • Error while importing dxf to section wizard in Staad Pro from AutoCAD

    I am analysing an RCC box girder for which some peculiar tapered sections have to be created. I created a tapered rectangular section in AutoCAD 2014. I used polyline to create the 2D and then extruded it to make it a solid 3D section. Now when I import…
  • Shear results from query dialog box and postprocessing are different, so which is correct, please help me

  • how to get the loadings details in report????

    I have got my report, but there is no loading details like dead load, Wind loads and all... In report settings i have added Loadings, but its not showing.... Wt to do???? i want to see other load details. How to get that details?
  • Moving Load - STAAD PRO

    I need help in STAAD PRO. I am trying to get a moving load to go from one node to another. For example, if I have nodes N1, N2 and N3, and member M1 runs from N1 to N2, while member M2 runs from N2 to N3. How do I get a moving load to move from member…
  • response spectrum analysis in STAAD

    Hi Three questions regarding the response spectrum analysis. Q1 : I am not quite sure why I got zero on the Y and Z directions? Please advise. LOAD 4 LOADTYPE Seismic TITLE RESP. SPECTRUM LOADS X MEMBER LOAD 15 TO 20 35 TO 40 UNI GX 10…