Browse By Tags

  • hi everyone, can anybody help me to solve this model because have error of the snow and seismic loads??

    STAAD SPACE START JOB INFORMATION ENGINEER DATE 30-Nov-22 END JOB INFORMATION INPUT WIDTH 79 UNIT MMS KN JOINT COORDINATES 55 468.544 16072.7 192.577; 73 507.061 16072.7 -1.061; 107 358.857 16072.7 356.735; 151 7030.99 14763.7 2911.01; 152 7609.76 14763…
  • WARNING: DESIGN OF SECTION FOR MEMBER # FOR PLATE SECTION

    Hello, I came across with an issue, could you please help me. I need to use plate member for stair stringer, Staad is showing errors for the analysis of the member. WARNING: DESIGN OF SECTION FOR MEMBER # Please help me how to rectify the…
  • Unable to start STAAD Pro Connect Edition V22 Update 7

    Hi. I recently got access to the student license of STAAD Pro. It was working well until last few days. The application is not starting. Below given screen appears and then there is no further movement in the loading. I tried re-installing the application…
  • PLATE STRESS AND CUTTING LINE DIAGRAM IN MIDAS GEN

    Dear Bentley members, I have tried Plate model in Midas Gen and staad pro, In Midas there was one option called Cutting line diagram for understanding the Plate bending diagram, Similarly is there any tool in Staad pro?. Or any method for understanding…
  • RCDC v10, beam design - Beam continuum section - Beam are considered as cantilever, where there should be support on both sides. No option to add support as column. Can you please clarify

    Hello, I would like to design with supports on both sides. I designed columns first in RCDC V10, then my etabs analysis fie (tables to access file) is used to design beams floor by floor. I am designing ground floor beams first. When I import the file…
  • Design of Solid slab (Conventional slabs)

    Hello Everyone For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…
  • Dummy beam

    Hello Everyone. I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?
  • How to create a cantilever slab by using the Physical modeler?

    How to create a cantilever slab without beams in the Physical modeler in STAAD connect edition?
  • RCDC Detailing Failure

    How to rectify this failure known as 'Detailing failure' in RCDC
  • Can I Reduce Development length of bars in the beam by using RCDC

    Hello Everyone How can I reduce the development length bars in the beam (Figure 1-1), I'm running to get a result like this beam (figure 2-1) Figure 1-1 Figure 2-1
  • Can I design a Continuous two slabs by using RCDC STAAD?

    Hello Sir RCDC is designed and Detailed all the slab one by one but I want to detail all Top and Bottom Reinforcement of the two-way slab once, what should I do.
  • Mton/Cm to Kn/m

    How do I change Mton/Cm to Kn/m
  • STAAD Webinar: Have no fear, Steel AND Concrete are here!

    It’s easier than ever before to take your project from analysis and design to automated drawing and documentation. Produce the bill of materials and gain instant insight into various design alternatives for the most cost-effective design. Please join…
  • Saad Pro

    I s there any way in Staad pro to design slim floor beam SFB where the Slab floor rests on the lower flange
  • Similar models showing very different results (Beam end forces, displacements, base pressure...)

    Hello, I´m designing two small guardhouses in STAAD.Pro V8i SS5, both are RC structures with slab foundations, they are almost equal in principal geometry, loading and sections, the only thing that changes considerably from one model to the other is the…
  • Problem modelling plates on top of beams for elevated steel water tank

    I am trying to model a Elevated steel water tank with bracing for analysis in STAAD.Pro. While modelling the structure I've encountered a problem and would like your help. The problem is: While the beam offset works perfectly for modelling a beam…
  • floor load

    Dear sir, In attached stad file .I am applying the dead load 2kn/m2 as floor load. 1.somewhere i am attaching two secondary beams with primary beams with the same node.is this load distributed all over the area same as 2kn/m2 or where i am having…
  • UC Ratio problem

    warehouse.zip wind calculation also in that folder.... try to fix this probem guys
  • Error while importing dxf to section wizard in Staad Pro from AutoCAD

    I am analysing an RCC box girder for which some peculiar tapered sections have to be created. I created a tapered rectangular section in AutoCAD 2014. I used polyline to create the 2D and then extruded it to make it a solid 3D section. Now when I import…
  • how to get the loadings details in report????

    I have got my report, but there is no loading details like dead load, Wind loads and all... In report settings i have added Loadings, but its not showing.... Wt to do???? i want to see other load details. How to get that details?
  • Free Seminar! STAAD Insider Skills Special Interest Group

    FREE Live Seminars to sharpen your skills. The Insider Skills - Special Interest Group series is offered weekly. STAAD is featured on week 3 of each month. The next STAAD session is October 16th. Event: STAAD Insider Skills – Special Interest…
  • STAAD.Pro V8i SELECTseries 4 QA&R 20.07.09.31

    I am excited to announce the latest new release of the STAAD.Pro V8i SELECTseries 4 QA&R has been published on the Bentley SELECT server and is now available for download. The new release has undergone not only the stringent quality assurance programme…
  • Bentley at the 2011 SEAoC Convention in Las Vegas

    Next week I will be representing Bentley Systems at the Structural Engineers Association of California's annual convention being held in Las Vegas. It's my first trip back to the convention in a number of years, and I'm excited to be back. If you're attending…
  • But I Don’t Want to Talk to a Salesperson!

    Structural engineering software is no longer a glorified calculator. Oh sure, years ago it was that 6-pack of beer you could pick up on any street corner, but not today. Today it's a sophisticated bottle of wine with earthy tones that is lined up with…
  • Re: Mat Foundation Issue

    I am new to STAAD Foundation and am having a similar issue. My project is to put a new building on a new mat foundation which is supported by existing (unevenly spaced) piles. I want to import my building model from STADD.pro into Foundation and see how…