Browse By Tags

STAAD SPACE START JOB INFORMATION ENGINEER DATE 11-May-23 END JOB INFORMATION INPUT WIDTH 79 UNIT METER KN JOINT COORDINATES 49 0 0 11; 50 4 0 11; 51 9 0 11; 52 14 0 11; 53 19 0 11; 54 22 0 11; 55 27.5 0 11; 56 33 0 11; 57 38 0 11; 58 43.5 0 11; 59 47…

Hello, I had a question regarding this simple circular tunnel model shown below. I have the following modeled to check the shear SQY. I know I'm missing something simple here so I hope I can get some help. L=100 ft (total longitudinal length)…

Hello Everyone For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…

How does Moment distribution and release for beams work in STAAD Pro ? While designing Secondary Beams, I’m releasing the moments MX, MY, MZ to a 100% at their ends. if I keep the ends fixed, I get a hogging moment say ‘ X ’ kN-m at the ends. However…

Dear All, Currently i'm designing a gantry crane. 1. I have assigned the loading from Crab to the gantry beam as moving load (Shows in Red color), But i have no idea how to assign the loading (Shows in Green color) when gantry crane is moving along…

Does anybody designed Gantry crane using STAAD.Pro? Can anybody explain how can i assign whole surface of the rail on the ground as fixed? do i need to divide the rail in to small parts and assigned those nodes as fixed? or do i need to design Gantry…

I am using Member loading ( UDL ) and getting warning in the analysis output, which for me seems like a software bug, can you please guide me. Input LOAD 20 WIND: WIND X MEMBER LOAD 13 UNI Y 3.28 0 3.25 0 I have give f1,f2,f3 and f4 as the manual…

Buen día amigos, tengo una duda, de alguna manera se puede configurar staad.pro, para que cada propiedad (perfil) lo ponga con diferente color, ya que en mis modelos solo me los da en 2 colores teniendo 5 propiedades distintas..

Dears, Concerning the design of RC beams in a PT slab, i am trying to determine the most accurate way to design the beams (determining top and bottom reinforcement). in Ram concept all design procedure is based on design section analysis. i prefer designing…

I have designed a steel structure in Staad pro, No errors are found but in output file some members are getting failed. I dont have any ideas in passing those members. If I change section of those members other members are getting failed. please sort…

Hi, I'm modelling a circular silo and assign incline supports and compression only(KFX) supports, but half of the tank support reaction results into X direction is Positive(+) and the other half support reactions into X direction is Negetive (-). Can…

I'm working in built-up column with four I sections. I'm getting some results and not sure the results are correct. Can someone please check the model is correct? Thank you. Built-Up column.STD

Dear sir, good day, I design the attached structure in two ways. when I design it without considering the concrete plate it gives very less utilization ratio? and when I design it without considering the concrete plates on the top of beam it is getting…

I mistakenly converted my input file to single line format. Is there any way to get it back to list format without a lot of keyboard time?

How can i define a new timber material within Staad.Pro with given values for Bending strength etc rather than using a set value such as C16 timber? Any help would be greatly appreciated as this is for my Dissertation.

HELLO, Is it possible to design the composite beam and composite column in staad ? if not then how do i design it in staad. with the help of macros or what?

Hai friends Please help us to solve problem with STAAD section informations. Staad developers kindly advice us. All query mentioned in the attached word file Thanks for ur support in advance Regards Bagmass

hello, 705 715 START FX FZ MX MY 705 715 END FX FZ MX MY . these are the release specification given and one more think is that i my beam is incline.

Hello! I am new to ISM, and am experimenting with it as a central repository for Prostructures design and STAAD Engineering data. It seems to work at first attempt, but I am having an issue with materials. It seems that the mapping of materials from…

Good morning, I am facing a problem in the attribution of BEta angle. This property disappears when i am restarting the program and reopening the STD file. Is there any solution for keeping it ? Image 1: BETA=0degmage 2: Beta=90deg …