Bentley Communities
Site
Search
User
Site
Search
User
Welcome
Products
Support
About
More
Cancel
Browse By Tags
All tags
calculation
PLAXIS 2D
arc-length
arc-length control
calculating
calculation error
calculations
cancel
Command
command file
consolidation
cylinder
desired maximum
Geotechnical Analysis
iterative settings
kernel
latin
mesh
phases
PLAXIS
PLAXIS 3D
preview
recalculate
Tips and Tricks
unicode
wizard
Workflow
Non zero cohesion and tensile strength
Dan Sandilands
Is there an official Plaxis reference or literature reference supporting the use of non zero cohesion and tensile strength (eg 1 kPa), to improve numerical calculation?
Answered
5 months ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Forum
What is the meaning of "Maccel" value in the calculation kernel?
Samet Ozenc
Hello everyone I wonder about the meaning of the Maccel value. I checked the Plaxis 2D reference manual and it says "The value of this parameter is always 0." Why it's always zero and what does it do? Thank you
Answered
over 1 year ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Forum
Launch PLAXIS 2D calculations via DOS commands
Micha van der Sloot
Application PLAXIS 2D Version PLAXIS 2D 2010 Date created 11 October 2012 Date modified 11 October 2012 With PLAXIS 2D it is possible to load, calculate and save a PLAXIS 2D project via an MS-DOS command line. This…
over 3 years ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Wiki
Set multiple phases to be calculated
Micha van der Sloot
Application PLAXIS 2D PLAXIS 3D Version PLAXIS 2D PLAXIS 3D Date created 24 July 2012 Date modified 24 July 2012 A simple trick when one wants to recalculate a lot of phases, is to CTRL+Click on the phase icon in…
over 3 years ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Wiki
Iterative settings: desired minimum and maximum
Micha van der Sloot
Application PLAXIS 2D PLAXIS 3D Version 3DFoundation PLAXIS 2D Date created 18 July 2011 Date modified 18 July 2011 The iterative parameters Desired minimum and Desired maximum are primarily meant to determine when…
over 3 years ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Wiki
Iterative settings: Influence of Arc length control
Micha van der Sloot
Application PLAXIS 2D PLAXIS 3D Version PLAXIS 2D CE V20 PLAXIS 3D CE V20 Date created 18 July 2011 Date modified 7 September 2020 Assume on a certain geometry the user wants to apply a certain load, but during…
over 3 years ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Wiki
Continue a cancelled calculation phase
Micha van der Sloot
Application PLAXIS 2D Issue status Open First Affected Version PLAXIS 2D 2010 Found in Version PLAXIS 2D 2010 Fixed and Released in Version Issue # 14287 Date created 10 October 2011 Date modified…
over 3 years ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Wiki
2D Consolidation phase does not calculate
Micha van der Sloot
Application PLAXIS 2D Issue status ✔ Solved First Affected Version PLAXIS 2D 2010.01 Found in Version PLAXIS 2D 2010.01 Fixed and Released in Version Solved in a recent version Issue # 14664 Date…
over 3 years ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Wiki
PLAXIS 2D 2010 does not save correctly when using non-Latin characters
Micha van der Sloot
Application PLAXIS 2D Issue status Open First Affected Version PLAXIS 2D 2010 Found in Version PLAXIS 2D 2010 Fixed and Released in Version Issue # 14400 Date created 29 August 2011 Date modified…
over 3 years ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Wiki
PLAXIS 2D Tunnel Designer
Micha van der Sloot
Application PLAXIS 2D Version PLAXIS 2D Date created 09 May 2011 Date modified 09 May 2011 --> In this video we demonstrate the PLAXIS 2D Tunnel Designer. It can be used to design tunnels (e.g .bored tunnels…
over 3 years ago
GeoStudio | PLAXIS
GeoStudio | PLAXIS Wiki