Browse By Tags

W726-6: Near zero length element at point XXX warning message in AutoPIPE

Mike Dattilio

Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Warning Message Original Author: Bentley Technical Support Group Problem…
- 3 months ago
- AutoPIPE
- AutoPIPE Wiki
AutoPIP Load Transfer to STAAD

Aslinn Aijian Zha

Hi, is it possible to transfer the non-code combinations from Autopipe to STAAD when using the PipeLINK workflow? By default it only transfers the primary load cases. I found an old post here: Mike Dattilio's Activities (rssing.com) saying ' AutoPIPE…
- Answered
- over 1 year ago
- AutoPIPE
- AutoPIPE Forum
2D DXF Export SS4 and older vs SS6 and latest -reg.

Dani Paul

Dear Colleagues, When I tried to 2D DXF Export my STAAD model having Member / Plate Elements, quite surprised to see that SS6 (20.7.11.82) and the CONNECT Edition (21.3.0.146) was not able to carryout the 'export' properly when as compared with SS4…
- over 4 years ago
- RAM | STAAD | ADINA
- RAM | STAAD Forum
03-s. Export Model to STAAD using ISM (*.)

Mike Dattilio

Bentley’s Integrated Structural Modeling (ISM) allows structural engineers and designers to share structural engineering project information among modeling, analysis, design, drafting, and detailing software applications. More details on the philosophy…
- 1 month ago
- AutoPIPE
- AutoPIPE Wiki
03-s: Export Model to STAAD Using PipeLink (*.pipelink) command in AutoPIPE

Mike Dattilio

Comments, Questions, and Answers about exporting a file to STAAD using PipeLINK Attention: Please see the following document installed with AutoPIPE: PIPELINK_tutorial.pdf Item #0: Export model to STAAD using "Model to STADD using Pipelink (*.pipelink…
- 1 month ago
- AutoPIPE
- AutoPIPE Wiki
09. IF STAAD is Not installed on the computer, can AutoPIPE still export a file using PipeLink?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: IF STAAD is Not installed on the computer, can AutoPIPE still export a file using…
- over 5 years ago
- AutoPIPE
- AutoPIPE Wiki
08. Supports are not aligned in STAAD as were seen in AutoPIPE, why?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: When exporting model to STAAD, the supports are not aligned as in AutoPIPE, why: …
- over 5 years ago
- AutoPIPE
- AutoPIPE Wiki
07. AutoPIPE's 'Hydrotest' load combination was not exported to STAAD, why?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: AutoPIPE's 'Hydrotest' load combination was not exported to STAAD, why? Solution…
- over 5 years ago
- AutoPIPE
- AutoPIPE Wiki
06. When exporting a AutoPIPE model to STAAD the following screen appears and the "Close" button remains grayed out, why?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: When exporting a AutoPIPE model to STAAD the following screen appears and the "Close…
- over 5 years ago
- AutoPIPE
- AutoPIPE Wiki
05. No load information was exported from AutoPIPE to STAAD. Why?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: It appears that the loads in AutoPIPE are not being exported to STAAD. Why? Solution…
- over 5 years ago
- AutoPIPE
- AutoPIPE Wiki
04. Will the exported AutoPIPE information to STAAD include weight and stiffness, as to analyze both mode shapes at the same time?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: Will the exported AutoPIPE information to STAAD include weight and stiffness, as to…
- over 5 years ago
- AutoPIPE
- AutoPIPE Wiki
03 Can AutoPIPE export the beam structure to STAAD using pipelink?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: Can AutoPIPE export the beam structure to STAAD using pipelink? Solution: Please…
- over 3 years ago
- AutoPIPE
- AutoPIPE Wiki
02. Is there a limitation for exporting loads to STAAD using pipe link? if so how many?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: Is there a limitation for exporting loads to STAAD using pipe link? if so how many…
- over 3 years ago
- AutoPIPE
- AutoPIPE Wiki
01. Is the integration between AutoPIPE and STAAD.PRO software version dependent?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: Is the integration between AutoPIPE and STAAD.PRO software version dependent? Solution…
- 1 month ago
- AutoPIPE
- AutoPIPE Wiki
00. How to export model from AutoPIPE to STAAD using Export> Model to STADD using Pipelink (*.pipelink) command?

Mike Dattilio

Applies To Product(s): AutoPIPE, STAAD Version(s): ALL; Environment: N/A Area: Import Original Author: Bentley Technical Support Group Date Logged Dec. 2017 Problem: How to export model from…
- over 3 years ago
- AutoPIPE
- AutoPIPE Wiki
03-s Export Model to STADD using SQLite Pipelink (*.pipelink)

Mike Dattilio

Applies To Product(s): AutoPIPE, STAAD Version(s): ALL; Environment: N/A Area: Import Original Author: Bentley Technical Support Group Date Logged Dec. 2017 Problem: The Pipelink database format…
- over 5 years ago
- AutoPIPE
- AutoPIPE Wiki
Export a Model from STAAD.Pro to PDS - Intergraph (frameworks Plus)

Jorge Ochoa León

Dear Comunity. It is possible to export a Model from STAAD.Pro to Intergraph's Frameworks, and I'd rather more than a just a DXF since I'm looking forward to getting as many profiles properties possible exported. Thanks!
- over 6 years ago
- RAM | STAAD | ADINA
- RAM | STAAD Forum
Exporting .DXF from STAAD

Maen Abdulhaq

I have two issues: -I tried to export .dxf from STAAD and saved that file, but when tying to open it with AutoCAD 2006/2015 nothing was shown on screen and even like nothing was exported. Do Ihave to select members or do some previous step before? - Is…
- Answered
- over 8 years ago
- RAM | STAAD | ADINA
- RAM | STAAD Forum
Re: Import/Export

Sye

To the best of my knowledge STRAND7 can directly import a STAAD model ( .std ). You may check with STRAND technical support on whether they can export data to STAAD.Pro or not ( most likely not ). If so, you may try exporting the analysis model from STRAND…
- over 10 years ago
- RAM | STAAD | ADINA
- RAM | STAAD Forum
Re: Only 1 member showing in STAAD (imported from BE Structural)

Steve Cocchi

Sharon, I have those same two versions installed and have done a *lot* of STAAD exports... So the versions themselves are not the problem. Try this: Unload all of your current section files, then load back just one of them (whichever might be appropriate…
- over 14 years ago
- RAM | STAAD | ADINA
- RAM | STAAD Forum