Browse By Tags

How to generate floor loading on an inclined floor/roof ?

Modestas

Applies To Product(s): STAAD.Pro Version(s): ALL Environment: ALL Area: Modeling Solutions Subarea: Loading Original Author: Abhisek Mandal, Bentley Technical Support…
- 6 months ago
- RAM | STAAD | ADINA
- RAM | STAAD | ADINA Wiki
RM Bridge FAQ: Modeling inclined pylon

MarcosBeier

For modeling an inclined pylon in RM Bridge the user can either have the cross-section of the element in-plane, with the usual option of the cross-section plane horizontal, or perpendicular to the element axis. These inclined element cross-sections…
- over 2 years ago
- LARS | LEAP | OpenBridge | OpenTunnel | RM
- LARS | LEAP | OpenBridge | OpenTunnel | RM Wiki
MICROSTRAN SUPPORT

YERALDIN LINDA BERRIOS ZURITA YERALDIN

Good morning: 3, I am using the microstran software but I have problems with the inclination of the support, you know how it can be done
- over 2 years ago
- RAM | STAAD | ADINA
- RAM | STAAD Forum
OBM Rotating bearings

MarcosBeier

OpenBridge Modeler allows setting the bearings directions related to the piers and abutments definitions or to the girders and deck. Initially, the user should have the Elevation Constraints for the Top Slope in the Substructure Placement set to Parallel…
- 8 months ago
- LARS | LEAP | OpenBridge | OpenTunnel | RM
- LARS | LEAP | OpenBridge | OpenTunnel | RM Wiki
02. How to model slopped pipe supports using AutoPIPE?

Mike Dattilio

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Modeling Date Logged & Current Version July 2021 12.06.00.48 Problem: Model a pipe section that is lying on a slope, and to know the normal force that the…
- 4 months ago
- AutoPIPE
- AutoPIPE Wiki
UNABLE TO GENERATE INCLINED FLOOR LOAD.

Rohit Babje

STAAD SPACE START JOB INFORMATION ENGINEER DATE 02-Feb-19 END JOB INFORMATION INPUT WIDTH 79 UNIT METER KN SET FLOOR LOAD TOLERANCE 0.01 JOINT COORDINATES 1 0 0 0; 2 4.95 0 0; 3 7.975 0 0; 4 11.94 0 0; 5 15.94 0 0; 6 19.855 0 0; 7 24.025 0 0; 8 27.94…
- over 4 years ago
- RAM | STAAD | ADINA
- RAM | STAAD Forum
08. Will "Inclined" wind direction set to off global axis take care of user required eccentric, torsional, or pitched loading of FPSO or off shore platforms in AutoPIPE?

Mike Dattilio

Applies To Product(s): AutoPIPE, Version(s): ALL Environment: N/A Area: Load Original Author: Bentley Technical Support Group Problem: Will "Inclined" wind…
- over 6 years ago
- AutoPIPE
- AutoPIPE Wiki
RE: Plate Mat Foundation query

Sye

Since the soil would be providing radial support to the wall offering resistance to it’s expansion, you will be better off modeling these as inclined supports. You can define radial inclined supports all along the circumference at various heights. At…
- over 8 years ago
- RAM | STAAD | ADINA
- RAM | STAAD Forum
Wind load on inclined member

Sye

Applies To Product(s): STAAD.Pro Version(s): ALL Environment: ALL Area: Load Generation Subarea: Wind Load Generation Original Author: Sye Chakraborty, Bentley Technical…
- over 8 years ago
- RAM | STAAD | ADINA
- RAM | STAAD | ADINA Wiki
How to applying moving load on a beam which is not parallel to any axis in the plane?

Debayan Banerjee

Hi, I have a beam in the XZ plane, but it is neither pararell to X nor Z axis. I have to apply a moving load to that beam. Is that possible? Since staad only asks for increments in the x or z axis. If not then is there any work around? Pls find attached…
- Answered
- over 8 years ago
- RAM | STAAD | ADINA
- RAM | STAAD Forum