Bentley Communities
Site
Search
User
Site
Search
User
Welcome
Products
Support
About
More
Cancel
Browse By Tags
All tags
report
analysis
acceleration
AutoPIPE
center of gravity
disconnect
Dynamic Analysis
FAQ
Flange Analysis
frequency
gravity
Maxsurf
Maxsurf Stability
missing mass
modal
MSRS
Output report
report setup
Response Spectrum
results
Segment
STAAD
Stability
Sub-report
time history
Time History Post Processor
ZPA
Center of gravity in a report
Dimitri
Dear all, I would like to give the center of gravity of my structure in my report. I know how to get in in my output file but I don't know how to put it in my report. Can someone help me please ? Regards, Dimitri
over 2 years ago
RAM | STAAD | ADINA
RAM | STAAD Forum
02. What formulas and how AutoPIPE calculates the accelerations of the valves, equipment and different points of a model?
Mike Dattilio
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Date Logged & Current Version April. 2021 12.05.00.16 Problem: What formulas and how AutoPIPE calculates the accelerations of the valves, equipment…
over 2 years ago
AutoPIPE
AutoPIPE Wiki
Maxsurf Stability Report
NA Maruf
Hi, I would like to get a Global Criteria Table after each load case stability analysis. Could you please tell me how can I do it? I have tried the following custom templates. However, the problem is the values come without a good format, without table…
Answered
over 3 years ago
MAXSURF | MOSES | SACS | OpenWindPower
MAXSURF | MOSES | SACS | OpenWindPower Forum
03. Why does AutoPIPE's Time History output report results not coincide with "Time History Post Processor" results?
Mike Dattilio
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Area: Results Original Author: Bentley Technical Support Group Date Logged & Current Version Mar. 2015 09.06.01.10 Problem…
over 4 years ago
AutoPIPE
AutoPIPE Wiki
02. Is there an option to output a time-dependent restraint reaction rather than merely the peak reaction which is output by default in AutoPIPE reports?
Mike Dattilio
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Area: Time history Original Author: Bentley Technical Support Group Date Logged & Current Version Mar. 2015 09.06.01.10 Problem…
over 4 years ago
AutoPIPE
AutoPIPE Wiki
01. When running Time History analysis, do supports indicate restraint reactions in AutoPIPE's output report?
Mike Dattilio
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Area: Original Author: Bentley Technical Support Group Date Logged & Current Version March 2015 09.06.01.10 Problem: When…
over 4 years ago
AutoPIPE
AutoPIPE Wiki
06. Where are the missing mass mode in individual Modal results in AutoPIPE's output report?
Mike Dattilio
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Results Original Author: Bentley Technical Support Group Date Logged & Current Version Dec. 2016 10.01.00.09 Problem: Where are the missing mass…
over 5 years ago
AutoPIPE
AutoPIPE Wiki
01. Why does results of a dynamic analysis show that the response accelerations are lower than ZPA at most of the nodes in AutoPIPE Accelerations output report?
Mike Dattilio
Applies To Product(s): AutoPIPE Version(s): V8i and higher Area: Report Original Author: Bentley Technical Support Group Date Logged & Current Version Dec. 2016 10.01.00.09 Problem: Why does results…
over 5 years ago
AutoPIPE
AutoPIPE Wiki
01. What options are available to increase the participation factors in a model with multiple disconnected systems in AutoPIPE?
Mike Dattilio
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Original Author: Bentley Technical Support Group Date Logged & Current Version Feb. 2017 10.01.00.09 Problem: What options are available…
over 1 year ago
AutoPIPE
AutoPIPE Wiki
03. Why does AutoPIPE state that the frequency sub-report for all the pipe runs are the same?
Mike Dattilio
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Results Original Author: Bentley Technical Support Group Date Logged & Current Version Feb. 2017 10.01.00.09 Problem: Why does AutoPIPE state that…
over 4 years ago
AutoPIPE
AutoPIPE Wiki
a. "Flange Analysis" sub-report in AutoPIPE
Mike Dattilio
Comments, Questions, and Answers about AutoPIPE's Flange Analysis Sub Report What does "Inside diameter of flange should be equal to inside pipe/nozzle diameter" mean in the Flange Analysis Output report? Flange Analysis report does not contain…
7 months ago
AutoPIPE
AutoPIPE Wiki
Q. What does "Inside diameter of flange should be equal to inside pipe/nozzle diameter" mean in the Flange Analysis Output report??
Mike Dattilio
Applies To Product(s): AutoPIPE, Version(s): ALL Area: Analysis Original Author: Bentley Technical Support Group Problem: The following is displayed in the report Flange analysis Output report…
9 months ago
AutoPIPE
AutoPIPE Wiki