Browse By Tags

  • R3-8 Lane Control Sign

    Product: OpenRoad SignCAD 2023 Version: 23.00.00.151 Area: How-to Original Author: Bentley Global Technical Support Introduction: The instructions below show how-to create a R3-8 lane control…
  • Predefined worksets as templates for every single WorkSpace

    The standard setup is that you make a workspace, and then a workset, and then you can use the created workset as a template for the next workset, but how do i force the list of templates to be a managed folder where i have made a number of worksets that…
  • 在OBM中,需要梁模板的上部跟随桥面板倾斜,但下部垂直不变,该怎么做?

    我尝试过将梁模板里下部的点都勾选了“DO Not Rotate”,梁模板坡度变为0,并True "Use Beam Rotation". 但这样做了之后,梁模板上部确实跟随着桥面板一起倾斜,但下部也倾斜了,如何使它能够垂直呢? (主要是桥是斜交并且变坡的,不然可以只变动梁模板上部的坡度,再False "Use Beam Rotation".)
  • Feature not showing in 2d - concrete barrier

    hi, I have a conc. barrier in my master temple. A barrier hinge feature def. is being used on both the top (BH1-L and BH1-R) and bottom hinge points (BH-L and BH-R) , however in the 2D plan its only showing the top hinge. (BH1-L and BH1-R). Again the…
  • End Condition Exception Not Following Horizontal Feature Constraint

    I am trying to apply an end condition exception to a template that has a right outside edge of pavement that is controlled by a horizontal feature constraint so the outside edge of pavement is able to vary (for example, at a turn lane taper transition…
  • Template appears normal in Template Studio and Quick Log but have error 'A template associated with the selected profile is no-longer availble' when using log report.

    Hello, I have updated an existing tempalte and saved to the config file with no issue. Upon setting the new tempalte as a default for the location type and trying to 'Log Report' I get the below error; The template appears properly in Template Studio…
  • Corridor Templates - Automatic update of constraints

    I have this template and would like the point BallastBtm to automatically move horizontally based on the relationships between other points in the template, specifically to find the lowest point from SB1 TO SB8 and move horizontally to x point = 0 (e…
  • Distances in the Pile Layout

    In OpenBridge Modeler the distances in the Pile Layout Tab can be manually edited to update the model individually with the pile's on-site construction errors. Local eccentricities can be added to the model by modifying the current pile Distances. The…
  • 请问ORD每次打开廊道模板都会提示缺少配置是什么原因呢?

    每一次打开ORD的Template之后,都会提示: 然后也看不到任何模板: 必须要手动选择模板文件才行,请问如何解决?需要手动设定默认模板路径?
  • End Condition Exception - Components Distorted

    Hi I have a template with pavement layers extended to End Conditions. I have applied end condition (Override) and removed "check for interception" from fill component. The constraints of the marked points are getting removed in the end condition exception…
  • OBM Deck Template into RM Modeler

    OBD CE 2022 Release 1 and RM Bridge v11.14, the User can import OBM Deck Templates into RM Bridge for structural analysis, following the below steps: 1.OBM Create Deck Template In OBM > Utilities > Libraries > Decks, create a new deck cross-section…
  • Munsell Soil Colours on Log

    Is there a way to colour the soil "Graphics bar"? From the options (see attached pdf), the only option is for the border colour, which impacts the border and not the graphic. There are at least 100 colours on the Munsell Colour Chart. Coding would seem…
  • End COndition Exception Parent Component Relationship

    Hi, I have a corridor which has a berm and end condition arises from the berm. I had made the end conditions as child component of the Berm. When I apply end condition exception, the end conditions do not respect the parent child relationship. The end…
  • Issues with Tunnel Templates | Closest ComponentConstraint | Tunnel Component rendering

    Hi guys, I'm currently working with this template, observe the selected Line component, it has two ends right and left as marked below. Issue #1 My goal is to project the line ends to the tunnel inner ring. The level of this line will vary depending…
  • Creating a Template for Circular Tank in Physical Modeler

    Hi, I'm creating a template for a circular tank for a project. I got stuck in XML code for the trapezoidal load application of surcharge and earth pressure. Can you kindly share the XML code for applying Earth pressure and surcharge loads only to…
  • Templates - Establishing relationship in Tunnel Templates

    Hi folks, I'm trying to establish a relationship between Two Points and one component. My goal is whenever " Single_Track_LR " go up or down, " SC_Left_Edge " point should also go up or down vertically but get attached to " Tunnel_Inner_Face " component…
  • New Document Wizard: Is there a way to store the name (and location) of the template file in the new file attributes?

    Searched the community forum for this can found nothing (either nobody has asked or its asked in a different way) Is there a way to store the file name and the location (either as pathname\filename or as PW link) of the template file that was used…
  • How do I add a new Feature definition/ Cell Library for UK standards for a new Chamber in ORD

    I am using Uk standards Library for designing Stormwater drains. How do I add a new Feature definition/ Cell Library which is not in the Cell Library for a new Chamber (image attached for reference) in ORD. I tried using the Add New Template option and…
  • Editing in Station Offset Reports

    Hi all, I have a corridor of 4 Lane divided carriageway and I need to create a lane slopes report @ 10m interval. I ran the station base report . The camber/Lane slope in reports is calculating from centerline "CL" to carriageway edge "EOP" which is…
  • Editing barrier template's variable constraints breaks all parameters on barrier template drop

    I'm attempting to use the Variable Constraint window to make the shape of a barrier rail vary along the length of a single span. I made a template for the barrier rail, where I defined all of the constraints I would need to adjust: I placed the barrier…
  • 改变Linear Feature的材质

    老师好, 我在ORD模型中需要加入一个护栏(如图1所示)。 (图1) 护栏实现的方法,用了在template中设置linear feature的方法(如图2所示)。 (图2) 问题是,在生成的护栏模型中,木块的材质显示不正确(如图1中,是白色的)。请问如何改变该护栏木间隔块的材质,在保持其余部分材质不变的条件下?是否可行? 然后,我有一个更普遍的问题,请问如何建立或编辑ORD模型中的这些feature?有一个feature editor那种一站式的编辑器吗?是否有有关feature的介绍或者教程材料可供我学习…
  • Component not connecting/ Floating Component

    Anyone know what would cause this component to become unattached? The template doesn't show this, but when generating dynamic sections as well as actual sections it is just floating there.
  • Linear Element missing profile from template??

    I am trying to grab the EOP line from my corridor model to use as an intersection point for the driveway CL I am drawing (red line). When I try to grab the EOP line, I get an "Invalid Geometry Type" error. But there the CURB_FACE_TOP_L line is right next…