This command provides simple drivers eye view through the model relative to reference geometry with user defined offsets and a surface mesh, that can be animated at a user defined speed to help validate simple line of sight model integrity.
... Read more.This command provides a summation of a group of mesh elements contained within a fenced area. The Top Slope Area, Planar Area, and Volume are displayed in a measurement tabbed view.
Finding the command
[Note: This command will only be active...
Read more.This command provides a dynamic measurements perpendicularly from a baseline to a defined point of interest to aid in checks like lateral clearance.
Finding the commandFrom the Default Frontstage main toolbar, open the Civil Tools icon and select...
Read more.This command provides a dynamic slice through the 3D model perpendicularly to a baseline reference to allow detailed analysis along the baseline for greater insight into the model.
Finding the commandFrom the Default Frontstage main toolbar...
Read more.Even though I am in a 2D drawing, we are using ProStructures v10.7.2.33 (in MicroStation mode) as our base platform with Connect SDK v10.16.02.022 on Windows 11 Enterprise
I have an ECSchema that contains an ECClass which contains ECProperties and other...
Read more.For beam local Y is minor axis and KLR(or LR)value is more critical. KLR for beam 15 of attached model is 262.
This result is LR for major axis. Where is the result for minor axis?
By the way please advise if UNT and UNB for column is correct for parameter...
Read more.Apologies for missing this question. You can find slenderness ratios in both directions in the Output file if TRACK 2 design parameter is used:
UNT and UNB parameters are assigned correctly, assuming that bracings and cantilever beams do not provide any...
Read more.This command provides a summation of a selected mesh element. The Top Slope Area, Planar Area, and Volume are displayed in a measurement tabbed view.
Finding the commandNote: this command will only be active if a Civil schema is detected in the iModel...
Read more.This command produces a report on the quantities using elements located along an alignment. (Only visible elements will be taken into account)
Finding the commandCivil Reports can be found in a separate docking tab. These tabs can be relocated all over...
Read more.This command provides a dynamic slice through the 3D model to allow detailed/localized analysis for greater insight into the model.
Finding the commandFrom the Default Frontstage main toolbar, open the Civil Tools icon and select ‘2 Points Cross Section...
Read more.When using AutoCad Civil 3D with the ProjectWise integration, I sometime receive this error "Datasource connection terminated". Any ideas why this is happening or how to resolve this? I have to close out of my project after I close the error message box...
Read more.To select the unit system, click on the gear icon in the lower right-hand corner of the browser.

Under “User Settings” / “General” select the appropriate Unit System to use. Note: this is a per user setting.

![]()
The Civil Tools enable several detailed review workflows that are specialized for civil use cases and take advantage of Civil intelligence that is included in the iModel. The tools available and even some of the capability may change depending on the...
Read more.请问将CAD文件导入后可以自动测出管段长度,但是利用其相应的shp文件建模,为什么管段长度就测不出来了呢?(建模生成出来的模型非常小,好像是缩放了一样,而对应CAD文件没有这样)
Hi
I am trying to call a macro with a non-modal form from within another macro, which also has a non-modal form. Most of the time it works just fine.
However, about half of the time when I run the code, I get this "Can't show non-modal form when modal form...
Hi Paul,
I get this "Can't show non-modal form when modal form is displayed" error.
This is not MicroStation specific, but general VBA question, so I recommend to search and ask in VBA forums. Maybe StackOverflow or similar...
Read more.I sincerely invite Bentley expert to give some suggestion that if design parameters lz / ly / UNT / UNB is reduced by bracings?
For beam, usually ly is reduced by horizontal bracings(HB). But there are many different treatment of the other parameters from...
Read more.LY and LZ design parameters are used to enter the unbraced length for the purpose of computing allowable stresses in axial compression. UNT and UNB are used in specifying the unsupported length of the compression flange for the purpose of computing allowable...
Read more.
Cloud Services
Released 11th October 2023
Released 28th September 2023
Applies To
Product(s):
STAAD.Pro
Version(s):
CONNECT Edition
Environment:
ALL
Area:
Webinars, Events and Videos
Subarea:
Original Author:
Abhisek Mandal, Bentley Technical Support Group
...
Read more.
It is a pity that there is no expert who is ready to answer this question.
My question is if output of KLR(LR for tension member) for tension member is length between nodes despite that value of lz or ly is assigned as unbroken length?