• replied to this:
    Foundations- - Spread footing, strip footing ....

    Hello all

    OBD Update 10

    Am testing out the Structural tools.

    There does not seem to be a tool for 'Foundations: Spread Footing ..... or Strip Footing

    In the Catalogue there are 'Foundation | Mat Foundation, Foundation | Spread Footing and Foundation...

    Read more.
  • 02. Featured and Bugs Logged for AutoPIPE
    Problem: What enhancement / defects request have already been logged for AutoPIPE?

    Note:

    If an feature or bug has not been added to the program,

    • For features, use instructions here to log a new IDEA. The more votes logged per an IDEA, the quicker the CAE...
    Read more.
  • replied to this:
    Named Groups Dialog Box not appearing

    Hello

    From the Help Documentation

    'To Create a Named Group from the Named Groups Dialog

    1. Use the Element Selection tool to select the element(s) to be included in the named group.
    2. Select Drawing > Home > Groups dialog launcher.

      The Named Groups dialog...

    Read more.
  • RAM Element/ beam Module/ Tributary width/ wall footings

    I suggest to add a tributary width(ft) to the beam module, it will be just easy to enter loads in (psf).

    Any updates on addling wall footings to RAM Elements MODULES?

  • 03. How to update AutoPIPE with a new piping code or a new Code Compliance Calculation? or Can I use a different edition of the same code and get the same results until the new Piping code has been added to AutoPIPE?
    Applies To Product(s): AutoPIPE, Version(s): ALL Area: Piping Codes Original Author: Bentley Technical Support Group Problem:

    How to update AutoPIPE with a new piping code or a new Code Compliance Calculations? 

    Can I use...

    Read more.
  • replied to this:
    A problem during modeling surge valve at HAMMER software

    I have a transient model of pump failure, and I put a surge valve as a protective device. According to the following image and from the black line did not get back to the initial state of the system like it is failed.

    The hammer file is also attached.

    ... Read more.
  • replied to this:
    Pre qualified moment frame in RAM connection

    I need to specify and design WUF-W Moment Connection in RAM Connection, is it available? 

    Also I don't see the shear angle in RBS in smart connection.

  • replied to this:
    将三维约束好的参数化模型定义为单元后三维约束条件消失了

             

  • and 9 others earned the Ask A Question I achievement.
    Ask A Question I
  • I am designing a footing cap for drilled shaft using STM model as per AASHTO but getting error message for Tension ties in Z direction. it doesn't help if i provide hook or exra reinforcement.

    I am designing a footing cap for drilled shaft using STM model as per AASHTO but getting error message for Tension ties in Z direction.  it doesn't help if i provide hook or exra reinforcement. Could you please advise

    Thanks

  • replied to this:
    Update 10 - Quicksets seem to no longer be available

    Hello

    Update 10

    Just tried this ...

    'To Create a Quickset from the View Control Pop-up Menu

    1. Use the Element Selection tool to select the elements to be included.
    2. With the pointer in the view, press <Shift-Reset> to open the view control pop-up...
    Read more.
  • suggested an answer to this:
    Punching Shear Check - reduction in punch perimeter due to openings

    Hello,

    I am trying to perform some punching shear checks using RAM Concept, however, I am noticing that the program does not reduce the punch perimeter when there is an opening <10h away from column CL. According to ACI 318-14 Section 22.6.4.3, there...

    Read more.
  • replied to this:
    Add Flange - Doesn't seem to work with Update 10

    hello

    OBD Update 10

    Am running through some of the online training (pretty good overall) ...

    Am now on 

    Bentley OpenBuildings Designer CONNECT Edition User Accreditation Learning Path

    View Learning Path (bentley.com)

    Chapter 7: Advanced Modeling - The...

    Read more.
  • Windows are not showing as transparent

    OBD Update 10

    I've been trying out some windows.

    For some reason, some of them appear transparent, but others do now.

    I've tried changing the glass type (many times) in the property panel. Including to a glass type that does show up transparent in...

    Read more.
  • replied to this:
    RAM Element/Wood Design Ci design factor

    Any ideas; how can add Ci to the design of wood members?

    Thanks 

    Hazim 

  • License Issue

    My company has assigned me a license, but Connection Client still shows that I am under a seven-day trial.  Any suggestions to remove the trial notifications?

  • replied to this:
    <h1>Ahmed</h1>

    <h1>Ahmed</h1>

  • VBA script to detach display off borders from MicroStation connect edition ?

    VBA script to detach display off borders from MicroStation connect edition ?

  • Webinary

    Tutaj znajdą Państwo linki do zaplanowanych i już odbytych webinarów czy spotkań SIG/CC. 

    ________________

    Read more.
  • replied to this:
    PowerShell Create new ProjectWise folder from template and Excell file

    New-PWLogin
    
    $outfile = Get-TablesFromXLSXWorkbook -InputFileName 'C:\Users\joseph\Desktop\OutFile.xlsx '
    
    foreach($row in $outfile.rows)	
    {
        New-PWRichProjectFromTemplate -newFolderPathName $row.FolderPath -NewProjectName $row.FolderName -Template...

    Read more.