• suggested an answer to this:
    I am trying to optimize a hydraulic network in watergems using darwin designer. But I am getting an error "Feasibility check failed. No feasible solution exists with current input data". Could anyone please help me out

  • suggested an answer to this:
    [RM Bridge] Question about "CORIGID" in Modeler TCL

    The TCL is exported from RM Bridge Modeler, in the cross member definition part, it has several CORIGID commands

    GPCROSSMEM     "Diaphragm3-6"
    
    ......
    
    PART END
    
    CORIGID p10 A PART 1 "Segment6" co60 AS co10
    CORIGID p20 B PART 1 "Segment7" co30 AS co...

    Read more.
  • replied to this:
    End Condition Exception Not Following Horizontal Feature Constraint

    I am trying to apply an end condition exception to a template that has a right outside edge of pavement that is controlled by a horizontal feature constraint so the outside edge of pavement is able to vary (for example, at a turn lane taper transition...

    Read more.
  • replied to this:
    Could you help share Dataset for SCADA Connection using in Bentley Youtube training videos

    Hello,

    I'm watching Bentley's great videos about SCADA Connection in WaterGEMS on Youtube. However, I cannot find the practice files used in these videos.

    It would be great if you could show me where I can find them or a similar file I could use...

    Read more.
  • Behobene Probleme in MicroStation 2023.1 (23.00.01.44)
      Produkt(e): MicroStation   Version(en): 23.00.01.44   Umgebung: N\A   Produktbereich: Dokumentation und Hilfe   Produktunterbereich: N\A

    Das Team der MicroStation 2023 hat für das MicroStation 2023.1 zahlreiche Probleme in verschiedenen...

    Read more.
  • and 6 others earned the Ask A Question I achievement.
    Ask A Question I
  • asked a question in Hevacomp > Hevacomp Forum:
    Netsys ductwork sizing please - Technical Terms

    Hi, I'm new to Hevacomp and have a question on Netsys ductwork sizing please. Is there a technical explanation for the terms; Available Pressure, Required Pressure and Additional Loss Required (N/m²) values that are returned from the fan check? Thank...

    Read more.
  • Behobene Probleme in MicroStation 2023 (23.00.00.108)
      Produkt(e): MicroStation   Version(en): 23.00.00.108   Umgebung: N\A   Produktbereich: Dokumentation und Hilfe   Produktunterbereich: N\A

    Das Team der MicroStation 2023 hat für das MicroStation 2023 zahlreiche Probleme in verschiedenen...

    Read more.
  • WaterSight - New Administrator Guide
    1. Initial Setup Create a New Digital Twin

    If you are creating the first Digital Twin in your organization's account, follow the instructions in Create a New Digital Twin. If you are adding an additional digital twin, see Managing Multiple Digital...

    Read more.
  • WaterSight - Configuring Absolute Based Alerts
    Product(s): WaterSight Version(s): 10.00. Area: Documentation

    Background

    Alerts can be configured by the admin user in the Alerts Administration page and once generated by the system they become available in the Alert list page

    Alerts can be generated...

    Read more.
  • WaterSight - Current Simulation
    Product(s): WaterSight Version(s): 10.00. Area: Documentation

    Overview

    Investigate past, real-time and expected future performance for each asset using an embedded hydraulic model that is continuously updated with boundary conditions from sensors...

    Read more.
  • modify symbol changes not saving

    created symbol based on another.
    modify symbology , saved , went to use and changes not saved.

    NOTE timeline shown bottom right of all images

    .




  • What is an AutoCAD used for?

    Hi, I am Thamb Taklu from Western Steel Agency, i want to know What is an AutoCAD used for?

    Read more.
  • Dodanie poprzeczek do widoku modelu
    Produkt: OpenX Designer Wersja: 10 + Obszar:  Produkcja rysunku Autor: Klaudia Piekielniak

    Pytanie:

    Czy jest możliwość dodania przekrojów poprzecznych do widoku modelu (nie tylko w widoku rysunku oraz w arkuszach), tak aby można było je ręcznie...

    Read more.
  • WaterSight - Maps
    Product(s): WaterSight Version(s): 10.00. Area: Documentation

    p

    Overview

    The Maps page gathers the following information in one single view:

     Sensors (more information below)  Zones (more information below)  Large Customers (more information... Read more.
  • replied to this:
    How to Convert or Import EML to Lotus Notes NSF?

     If you are one of those who wants to Convert or Import EML to Lotus NSF, then I recommend you eSoftTools EML Converter Suite. This software helps you convert bulk files and any size of EML files. It comes with Naming Convention in these features you can...

    Read more.
  • 04. Support report indicates a load on a support who's open gaps never closed during an AutoPIPE Analysis, so why is there a load on the support in open gap direction?
    Applies To Product(s): AutoPIPE Version(s): ALL Area: Report Original Author: Bentley Technical Support Group Date Logged
    & Current Version June 2015
    09.06.02.06 Problem:

    When reviewing the load on a gaped support...

    Read more.
  • replied to this:
    asked a question in MicroStation > MicroStation Forum:
    [MS2023] WMS still dysfunctional

    We still see no improvements in WMS attachments even in latest Microstation 2023.

    Creating new WMS attachment is still dysfunctional despite multiple support requests. It defaults to WMS 1.3 version it can't show correctly and no option to switch to OGC...

    Read more.
  • API / Python scripting - PLAXIS

    This section contains examples and background information on the use of the PLAXIS Remote Scripting server API and the use of the Python wrapper.

    ... Read more.
  • suggested an answer to this:
    Results Scaling

    Hi,

    I am trying to change the scale in the Output File by clicking View > Scale > Manual (entering 0.05x10^-3), for I know that the load is very minimal and the deformations and stresses will really be small. but my output/ contour does not change. It...

    Read more.