Every time I try to run macro in STAAD I have below error message.
Even when I try to edit the code which I wrote and used before I have below error message and I can not edit.
I can not even import the vbs file. Please help me out and let me know What...
Read more.Check your code: Make sure your macro or VBS script is written correctly and does not contain syntax errors.
Update STAAD.Pro: Make sure you have the latest version of STAAD.Pro CONNECT Edition. Sometimes updates can fix known bugs.
Hello everyone, I am about to start the development of an application to incorporate into OpenUtilities Substation, I would be interested if you could provide me with an information link to start this development. Thank you.
Jon Summers in reply to Madelyn Reichel
Everything can be found on YouTube
Clearly you have no experience with the Bentley Developer Network, or the licensing terms applicable to third-party developers.
Damian Pavon in reply to Jon Summers
Hello! Thank you for your answers, just as Joe said, I contacted the email address he indicated, and they gave me the instructions. An annual developer subscription is required.
Hi all
The 3D model in the attached drawing contains a white element > an Extrusion Solid.
This was created with Extrude > without the Parametric Solid checkbox because otherwise the solid would not be created. The annoying thing about this Extrusion...
Read more.
Mark Stals in reply to Carl Myhill
Hi Carl, thank you for your reply. Lets hope development can find the reason for this mis behaviour
Carl Myhill in reply to Mark Stals
Initial review is suggesting the cause is related to 'Non-Manifold Geometry' where the reverse arc is meeting the line generating a very sharp edge and not the arcs themselves as first mentioned.
This is sill being investigated, will update when...
Read more.
A model footing is subjected to load eccentricity. How to measure the incremental rotation (tilt) with loading. It can be measured with difference in settlement in two node on opposite edge, but is there any short way to measure the tilt angle directly...
Read more.Thank you for your respond. I was looking for any procedure to get a curve of load vs rotation of footing, rather than checking rotation in individual phase.
Lanting Wei in reply to Atish Das
Dear Atish,
Have you found a way to get a curve of load vs rotation of the footing?
Thanks,
Lanting
Hi,
For a random wave response analysis, it is clear that we can define the wave spectrum in frequency domain. However, the available option for the output is in time domain. Is it possible to have the output results also in frequency domain? if yes,...
Read more.
I wanted to make some changes to the project file in PLAXIS2D connect client version 2022 using python interface. While I was doing so, after entering the required libraries and the server details, I am unable to even open the project file. The error...
Read more.
Stefanos Papavasileiou
Suggested Answer
Hello Meghna,
Sorry to hear that you experienced an issue with your automation.
In order to be able to assist you with your project and identify the reason for the problem you experience, please open a new Case for support.
Then, one of our support engineers...
Read more.
HOW TO MODEL SOFT SOIL CREEP MODEL IN PLAXIS LE?
vincent leong seng in reply to Faseel Khan
CAN GIVE ME A SOME EXAMPLE OF TUTORIAL HOW TO MODEL 1D CONSOLIDATION?
Faseel Khan in reply to vincent leong seng
Suggested Answer
You can see some of the distribution models on 1D consolidation such as a) Homogeneous Soil_GT; b) Layered Soils Case1_GT; c) Layered Soils Case2_GT; and d) Layered Soils Case3_GT.
For tutorials you can refer to the Consolidation Manual and in that you can...
Hello everybody,
I am having issues with template libraries losing the colours of the Feature Definitions (see image), the template does recognise the FD's (N-WE-VW\PVR) but doesnt show up red like it should (as defined in our Layer/FD DGNLIB).
... Read more.When using ByLevel symbologies, it is possible that the level settings are coming from a different DGNLIB and the Template Editor cannot use ByLevel unless the level exists physically in the active file. One the template is used by a corridor or linear...
Read more.Hi Caddcop,
You're absolutely right. For some reason, a few FD's were active in the DGNLIB that shouldn't have been active. Thereby causing the issues with making the template colours white.
I removed the duplicates and everything seems to...
Read more.
Hey everyone!
I'm a newcomer in Microstation but have a great experience in Rhino, Blender, Keyshot, Autocad.
I'm working for the company that uses MS for constructing some stands. I prefer to render them in Blender, so I need to export the files...
Read more.
How to model the Pipe Legs welded directly to the bottom korbbogen type head without pad?
Solution:Go through the below video to understand the process of modelling Pipe Legs welded directly to the bottom korbbogen type head without pad.
Read more.
The Home module is where you would land most of the time when you enter a project. This view gives an overview of the project and your usage. The displayed content includes Weather, Recent activity, My work, Create, iModels, and Summary.
The top bar...
N\A
Original Author:Jutta Eisenhauer
ProblemWhen activation of products from version XM (08.09.xx.yy) is not possible, the user must create...
Read more.
When working inside a Project, the Home Page is divided into three main parts:
In this section you will find all the information needed to work with ProjectWise powered by iTwin
Working with Documents
Read more.
ProjectWise powered by iTwin - FAQ
How do I access ProjectWise powered by iTwin?
Can I open ProjectWise 365 projects with ProjectWise powered by iTwin?
October 2023
A new datacenter, located in the European Union, is now available when Registering a Project in Bentley Infrastructure Cloud
The Media Explorer lets the user index and search through...
Read more.
It happen with all the macros I created not specific macro.
Everytime I try to import the vbs file I have that Error and I can not import them.
So I tried to create new macro and I could run and use that macro. But When I tried to run it later again,...
Read more.