Good morning, I have a skewed roadway segment. I was using the "Civil Cross section 2 Points" tool to get my section from my corridor. However, I dont know if there is a tool to get the same cross sections along the approach I mean at intervals. I'm using…

Does anyone know how to clip off part of the civil cell? I used intersection civil cell that joined by a template to form side road, see image. Add clipping reference worked only on the template part, but it didn't work on the civil cell.

I am trying to apply an end condition exception to a template that has a right outside edge of pavement that is controlled by a horizontal feature constraint so the outside edge of pavement is able to vary (for example, at a turn lane taper transition…

Hello, Currently i'm running into a problem regarding the function ' Synchronize from Library' on a template in my corridor, I didn't change anything in the template design. After using synchronizing, geometry that I added separately of the corridor…

I have a rough alignment in a river with two additional alignments on either side that represent the toe of slope. I created a template that essentially represents a river bottom with 2:1 slopes on either side. Whenever I try to add a point control that…

I'm having trouble getting components to display in my corridor. The linear features are all there, but only have components on the right side. I'm still new to OpenRoads (2020 Release 3 10.14.04.04) so I'm not sure what's causing this; probably something…

I am trying to generate cross slope report @ 10 m interval by station base or station offset report but i am not getting appropriate values of cross slope in report. It seems correctly in cross-section view. Am missing something ?? Images is ready for…

Hi All, I am trying to understand if there is any way I can find the name of the corridor and alignment to which my mesh belongs to? There has to be some relation, I want to read that information by Itemtype expression. Regards, Jaimin Pate…

Hi, Does anyone have some experience with discrepancies using corridor component quantities tool, I have been trying to get some quantities from a corridor that is attached as reference in a different working file. When I compared the quantities extracted…

Hi All, Hoping to have some advice on the following. When i run through the prompts of calculating super elevation once this has completed, nothing seems to apply to my lanes, nor does anything appear in my super elevation editor or superelevation viewer…

Hi I'm using Power Geopak V8i SS10. Very new user. I am working on modeling an intersection. I have laid out a pavement/wearing surface with edge of pavement lines. I applied my curb & gutter/sidewalk/tie as a linear template to EOP lines. When adjusting…

I am using Openroads Update 9 and have updated an alignment, but the corridor has not processed correctly. The alignment is in a seperate reference file and was updated using a complex redefine of the plan geometry. The profile was then adjusted to…

After creating and finishing a project using ConceptStation, I exported the project's elements to be used into ORD. The first time I tried to import the .ird I got the message that I had not imported the horizontal and vertical geometry beforehand. Therefore…

The above picture show the problem I'm facing. Is there a way to make ORD apply the 3% based on the modified point instead of the original?

My template is set up with priorities to solve for several cut and fill conditions. The guardrail end condition has the highest numerical priority and solved last. Naturally, this creates "pockets" of the guardrail shoulder condition along a corridor…

I have been trying to move from InRoads Suite to OpenRoads Designer. I have a design in ORD which has two intersection realignments and a main drainage way relocation. I have three road corridors and a ditch line corridor created. Now I have to mash all…

I am creating a 3D model for an urban, multi-lane widening project for FDOT. At the beginning and end of the project there is no profile grade required, since I am connecting to the existing pavement by milling (stripping) and resurfacing (overlay). From…

Hi Whenever I make a new corridor, the corridor feature lines seem to end up on the default level I have on. I am working on projectwise and my workmates don't seem to have the same setting. They go on different levels depending on what component that…

Good Afternoon, Using OpenRoads Designer CONNECT 2018 Release 3 (v.10.05.00.30), I am trying to determine the most efficient manner in which to rebuild our corridor objects. We have had issues working in files from several releases previous, however…

I am trying to calculate volumes of different layers of asphalt and different layers of groundwork. I've created a template which contains all these layers, where the final groundwork layer is variable (slopes and ramps or not). In my template this layer…

I have a surface that contains features only (non-triangulated). I am attempting to add it as a corridor reference so that I can set a style constraint in my templates. When I go to add the surface as a corridor reference, it prompts me to select the…