Select appropriate hyperlink below: Batch Processing, ITS, and ATS File / Model Management General Graphics Grids (Input & Results) Import and Export Libraries Loads and Load Sets Localization (Non…

AutoPIPEのワーニング, エラー, クラッシュなどについてのFAQまとめ forrtl: severe (24): end-of-file during read forrtl: severe (43): file name specification error Intel(r) Visual Fortran Run-time Error が表示される AutoPIPEからAutoPIPE Nozzleを開くと"No AutoPIPE Nozzle Identifiers…

Bentley communities site Note : a. user MUST sign into Connection Client in order to start licensing an application. Otherwise, user will have 7 days grace period from initial installed date or date or last successful sign in date. Otherwise, application…

Comments, Questions, and Answers about General piping code calculations in AutoPIPE Item #1: Ignore axial force Item #2: Which offshore design should be used? Item #3: Accuracy rating for results Item #4: Russian Codes (and ASME equivalents) …

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Date Logged & Current Version Aug 2014 09.06.00.19 Problem: Our Project Design Specification calls for ASME II 2010 for Material and ASME III 2007…

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Date Logged & Current Version April 2019 12.00.00.14 Problem: What Russian Codes (and ASME equivalents) can AutoPIPE be used for? Solution: Bentley…

Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Date Logged & Current Version April 2019 12.00.00.14 Problem: What is the accuracy rating for results in AutoPIPE compared to hand calculated values…

Applies To Product(s): AutoPIPE Version(s): ALL; Area: General Date Logged & Current Version April 2019 12.00.00.14 Problem: What piping codes should be used for offshore design? Solution: Consider using…

Applies To Product(s): AutoPIPE Version(s): ALL; Area: General Date Logged & Current Version April 2019 12.00.00.14 Problem: Why does AutoPIPE ignore axial force in most of the code equations? Solution: …

Comments, Questions, and Answers about AutoPIPE's Tie/Link Support Type: Item #1: Modeling Tie/Link supports See Also Different Types of Supports Flexible Joint Piping Components - Modeling Approaches Bentley AutoPIPE

Applies To Product(s): AutoPIPE, Version(s): ALL Environment: N/A Area: Modeling Original Author: Bentley Technical Support Group Jan 2016, AutoPIPE CONNECT 10.00.00.10 Comments…

Note: Please see the following AutoPIPE help section: Help > Contents> Contents Tab> Reference Information> Code Compliance Calculations> select a piping code to see the calculations performed by AutoPIPE. Item #1: Where are the design factors referenced…

Comments, Questions, and Answers: Note: For additional information about Stress Summary report beyond that in the AutoPIPE help, see the following "AutoPIPE_ASME_NB_Example.pdf" Document that was copied to your computer when the software was installed…

ATS release date Download ATS Currently available ATS versions: "Error - Cannot find File" message What is considered acceptable messages in the error log file? Expected difference from hand calculations to Results from AutoPIPE Reference…

Comments, Questions, and Answers: Item #1: Why does results of a dynamic analysis show that the response accelerations are lower than ZPA at most of the nodes in Accelerations output report? Item #2: Formulas to calculate accelerations at different…

Comments, Questions, and Answers related to Model input listing: Bend sub-report: Item #1: Confirm and modify the Bend and Tee flexibility factors calculated Item #2: Confirm and adjust the SIF of a bend Item #3: Calculate automatic bend radius…

Comments, Questions, and Answers related to Model input listing: Center of Gravity sub-report: Item #1: How does AutoPIPE analyze the deadweight? Item #2: How to find the weight of a component or selection set in AutoPIPE? Item #3: How to create…

The Snow Load dialog gives the user the ability to apply snow loads to segments of the model. When snow is applied, AutoPIPE creates a load in direction of gravity (simulating the real effects of snow in direct contact on a pipe), and can be defined through…

Comments, Questions, and Answers about AutoPIPE's Flange Analysis Sub Report What does "Inside diameter of flange should be equal to inside pipe/nozzle diameter" mean in the Flange Analysis Output report? Flange Analysis report does not contain…

1. Default Code and Non-Code Combinations in an AutoPIPE model 2. User Combinations as a Template for the Next Model User code or non-code combinations created in the program can be used as a template for other models with the same analyzed load cases…

Comments, Questions, and Answers on Component Data (Model Input) Listing in AutoPIPE output reports: See the following hyperlink for issues on the respective Component Data listing (aka Model Input Listing) report:Command: Tools> Model Input listing…

See the following hyperlinks for issue on the respective Analysis Output sub report: Command: Analyze model> Results> Output Report: Cover and Title page Displacement Beam forces Support General stress Restraint Preliminary…

See AutoPIPE's program help: Help > Contents> Contents Tab> Reference Information> Results Interpretation> review each document here: This appendix explains how to interpret AutoPIPE's output report results. The coordinate systems used for the results…

Applies To Product(s): AutoPIPE Version(s): ALL Area: Report Original Author: Bentley Technical Support Group Date Logged & Current Version Jan 2015 09.06.01.10 Problem: Can AutoPIPE…

Applies To Product(s): AutoPIPE, Version(s): ALL Area: reports / results Original Author: Bentley Technical Support Group Problem: AutoPIPE: results are 0 / zero Description: when viewing results…