• ASSEMBLY LLEG COMMAND EXPLANATION FOR MOSES LAUNCH

    Zain Abedin
    Zain Abedin
    • Launch Document.pdf
    • 6 months ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF I MOSES I SACS I OpenWindPower Files
  • Launch Analysis Error

    Arif Windiargo
    Arif Windiargo
    Hi Bentley there is an error when i'm trying to perform my own Launch Analysis. where i'm using my own SACS converted jacket .dat file. here was the log file of the errors. is there anything that maybe considered to be missing on my command line.…
    • 7 months ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower Forum
  • MOSES - ISO2020

    Arif Windiargo
    Arif Windiargo
    Dear Bentley Does MOSES latest update version (12.06.00.04) already accomodate ISO2020 for code checking? Best Regards
    • 8 months ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower Forum
  • #amass in moses

    Ju Peng
    Ju Peng
    Hi, everyone: In the moses manual ,the #amass is explained as above. for the parameter DISP, it says that the added mass will be DISP/G. when the analysis is under a SI unit , the added mass has a unit as MTON, so the DISP's unit in the #amass should…
    • over 2 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower Forum
  • MOSES Structural code chek during launch

    Gnaneswar sambhana
    Gnaneswar sambhana
    During Jacket launch structural analysis, which edition of AISC is used for Code Check of Beams in MOSES? Thanks in Advance
    • over 5 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower Forum
  • Why does the tilt pin have a big force when launch just begins?

    Ju Peng
    Ju Peng
    I have conducted a launch analysis with MOSES. then I use the command LWFORCE to explore the reaction force during the launch. I found that the pin force is not equal to 0 when event =0. Actually it is a big number. But obviously the jacket is not on…
    • over 5 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower Forum
  • QUESTIONS ABOUT EXPORTED LOAD WITH THE COMMAND 'LCASE -LAUNCH '

    Ju Peng
    Ju Peng
    I want to export all loads (included weight ,buoyancy , inertia ,drag load etc) at specified time during launch analysis .The commond I used is ' LCASE -LAUNCH ' AND EXP_ALOAD. The latest version of MOSES is used , so the loads are in SACS format . …
    • over 6 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower Forum
  • Free sliding during launch

    Jason Forcier
    Jason Forcier
    Q: How can I find out when free sliding occurs? REV 7.04 A: There is no unique answer to the question. MOSES reports the first time that no winch force is required to move the jacket at the specified speed. At times later, the winch may have to be applied…
    • over 7 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower - Wiki
  • Determine if 2nd tip has occurred, launch

    Jason Forcier
    Jason Forcier
    Q: How can I determine if 2nd tip has occurred? REV 7.05 A: Look at the results in the Skidway Reaction report. This is the table created by the "LWFORCE" command. The column labeled distance will have a "jump". The values in this column decrease as…
    • over 7 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower - Wiki
  • Rubbish for Longitudinal Strength results while the jacket is tipping during a launch

    Jason Forcier
    Jason Forcier
    Q: Why do I get rubbish for Longitudinal Strength results while the jacket is tipping during a launch? REV 6.01 A: Longitudinal Strength is applicable only to a single body. To find what you want here, do not include the jacket model for your check…
    • over 7 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower - Wiki