How to Add a Weldneck Stub End in OPM CE
Applies To
OpenPlant CONNECT Edition
Product(s):
OpenPlant Modeler
Version(s):
CONNECT EDITION (10.10.01.39)
Environment:
Windows 8.1/10 (64 bit)
Area:
Component
Subarea:
Graphics
Original Author:
…
How to Modify Hand Wheel Stem Thickness in OpenPlant Modeler CONNECT
Applies To
Product(s):
OpenPlant Modeler
Version(s):
CONNECT Edition 10.08.00.51 (Update 8)
Environment:
Windows 8.1/10 (64-bit)
Area:
Spec
Subarea:
Component
Original Author:
Aishwarya Kulkarni, Bentley…
How to Create New Spec Using OpenPlant Specification Generator CONNECT Edition.
Applies To
Product(s):
OpenPlant Modeler
Version(s):
CONNECT Edition 10.08.00.51 (Update 8)
Environment:
Windows 10 (64-bit)
Area:
OpenPlant Modeler Specification Generator
Subarea:
Spec Creation
Original…
How to get PIECE MARK information from Spec on all Piping Components in OPM CE
Applies To
OpenPlant CONNECT Edition
Product(s):
OpenPlant Modeler
Version(s):
CONNECT Edition (10.08.00.51)
Environment:
Windows 8.1/10 (64 bit)
Area:
Customization
Subarea:
Property
Original Author:
…
How to Create New Spec in OpenPlant Specification Generator
Applies To
Product(s):
OpenPlant Modeler
Version(s):
08.11.09.XXX (SS5) | 08.11.11.XX (SS6)
Environment:
Windows 7/8.1/10 (64-bit)
Area:
OpenPlant Modeler Specification Generator
Subarea:
Data
Original Author…
How to Update Graphics & Property When Spec Value Change
Applies To
Product(s):
OpenPlant Modeler
Version(s):
08.11.09.XXX
Environment:
Windows 7 (64 bit)
Area:
Components
Subarea:
Original Author:
Jaya Tiwari, Bentley Product…
RE: 2 different specs, hows does it decide which to pull the bolts from?
Hello Ben,
The selected spec under standard preferences queries the bolts form placement. For Example if you take bellows from ABCDE spec and trying to attach flange from 1234 spec it queries the second selection spec i.e. 1234.
However if you want…
"No Component Found With Initial Selection From Specs" Appears While Placing Component
Applies To
Product(s):
OpenPlant Modeler
Version(s):
08.11.09.XXX (SS5) | 08.11.11.XXX (SS6)
Environment:
Windows 7/8.1/10 (64 bit)
Area:
Component
Subarea:
Placement
Original Author:
Harpreet…
RE: OPM-SS6 - Gasket and Bolt missing from upgraded spec and catalog
Hello Tuan,
Yes you are correct it is simple to attach files here.
You can refer below wiki for general guidelines like attaching images, files etc.
http://communities.bentley.com/help/w/be_communities_help/5142.communities-forums-help
We will…
RE: Imperial specs inserting as metric
Hello Jason,
I am not able to download specs here. Can you please upload it again? In your Spec check Measuring unit what you have. Also please send the snapshot of affected component. Also what version you are using here.
-Regards | Rahul Kumar
How to Create Custom BW Valves with Nipples in OpenPlant Modeler
Applies To
Product(s):
OpenPlant Modeler
Version(s):
08.11.09.XXX (SS5) | 08.11.11.XXX (SS6)
Environment:
Windows 7/8.1/10 (64 bit)
Area:
Component
Subarea:
Graphics - Custom Component
Original Author: …
RE: Saddles in OPM
Hello Grant,
Can you provide some more input here? This will help us to assist you further.
Also Please check below wiki article on similar issue.
wiki - http://communities.bentley.com/products/plant/design___engineering/w/plant_design_and_engineering__wiki…
RE: Supports OpenPlant Modeler
Hi Jonatan,
It is because the active spec in Standard Preferences dialog doesn't have the supports you are trying to place. Please select the supports spec in standard preference as shown below:
After selecting the correct spec this error should…