• SIG Virtual Workshop: Bentley Offshore – Righting a Capsized Vessel with MOSES

    Kelly Fox
    Kelly Fox
    Bentley Offshore Special Interest Group: Righting a Capsized Vessel with MOSES Host: Geoff McDonald, Application Engineer, Offshore Bentley Systems, Inc. Presenter: S piro J. Pahos, Application Engineer, Offshore Bentley Systems, Inc. Date/Time: April…
    • over 3 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF I MOSES I SACS I OpenWindPower Announcements Forum
  • Mode Shape Stresses

    Mark Upston
    Mark Upston
    "Richard Brewer" wrote: Hello I am currently looking into performing a VIV (Vortex induced Vibration) fatigue analysis on a deepwater rigid spoolpiece. Is there any way we can output the stress associated with the modeshapes that have been calculated…
    • Answered
    • over 14 years ago
    • AutoPIPE
    • AutoPIPE Forum
  • External pressure consideration in deep offshore

    Mark Upston
    Mark Upston
    "Akin Akangbe" wrote in message news:487f653a@news.prod-bent.dmz... Am presently working on a deep offshore tie-in analysis. Can you kindly explain to me how I can consider the effect of external pressure in my analysis. Without inclusion of external…
    • Answered
    • over 14 years ago
    • AutoPIPE
    • AutoPIPE Forum
  • External pressure consideration in deep offshore - True wall force

    Mark Upston
    Mark Upston
    "Akin Akangbe" wrote: Regarding your response to previous discussion on bentley.autopipe Subject: Re: Hydrostatic Loading; Can you then confirm that AutoPIPE is not suitable for deep offshore analysis as regard to calculating true pipe wall force…
    • over 14 years ago
    • AutoPIPE
    • AutoPIPE Forum
  • 15. On long risers supported at the bottom, does AutoPIPE calculate the compressive stresses due to selfweight?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Environment: N/A Area: Modeling Original Author: Bentley Technical Support Group Date Logged & Current Version Dec. 2016 10.01.00.09 Problem: …
    • over 6 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 03. How to model riser clamps on subsea / underwater piping using AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Environment: N/A Area: Modeling Original Author: Bentley Technical Support Group Date Logged & Current Version Dec. 2016 10.01.00.09 Problem: …
    • over 6 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • Block moved after performing a UNION in the &SURFACE Menu?

    Jason Forcier
    Jason Forcier
    Q: Why does MOSES "move my block" a small bit when I perform a UNION in the &SURFACE Menu? REV 5.08 A: Yes, &SURFACE will "move your blocks around" if it has to eliminate undesirable intersections. In particular, the algorithm here relies on the fact…
    • over 7 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower - Wiki
  • Hull model composed of various pieces

    Jason Forcier
    Jason Forcier
    Q: Can I use a hull model composed of various PGEN definitions that share surfaces for hydrodynamics? REV 5.10 A: Absolutely not! You must have a single enclosed surface for hydrodynamics computations. You should use COMPART_SUM panels to make sure…
    • over 7 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower - Wiki
  • Hydrodynamic and Hydrostatic calculations

    Jason Forcier
    Jason Forcier
    Q: I have a piece that I want to be included for hydrodynamic calculations but I do not want it included for hydrostatic calculations. What options do I used in the definition? REV 7.04 A: You need to give the part just a little bit of displacement…
    • over 7 years ago
    • MAXSURF | MOSES | SACS | OpenWindPower
    • MAXSURF | MOSES | SACS | OpenWindPower - Wiki
  • 18. How to model a subsea expansion loop in AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i, CONNECT; Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group …
    • over 7 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 02a. Model Subsea (Underwater) Piping - AutoPIPE

    Mike Dattilio
    Mike Dattilio
    Frequently asked questions on modeling offshore underwater / sub sea piping: Modeling Pipe resting on the seabed floor Concrete Mattress Riser clamps Concrete Encased Steel Pipe Free catenary pipe Expansion…
    • 5 months ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 17. All hydrodynamic coefficients change significantly when a pipe comes close to, or lies on the seabed. Is this effect incorporated automatic in AutoPIPE's calculations?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged & Current…
    • over 8 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • Modeling Riser and Seabed Piping

    Mike Dattilio
    Mike Dattilio
    The attached file includes information and example models related to riser and seabed piping using AutoPIPE V8i.
    • Modeling Sea bed piping.zip
    • over 9 years ago
    • AutoPIPE
    • AutoPIPE Training Data Set