Applies To
Product(s):
CivilStorm, SewerGEMS, PondPack
Version(s):
CONNECT Edition, V8i
Area:
Output and Reporting
Original Author:
Mark Pachlhofer, Bentley Technical Support Group
Problem
After I…
Product(s):
WaterCAD, WaterGEMS, HAMMER, StormCAD, SewerCAD, SewerGEMS, CivilStorm, PondPack
Version(s):
V8 XM, V8i, CONNECT Edition
Area:
Modeling
Problem
How can I create a child scenario in a WaterObjects.NET project?…
Applies To
Product(s):
SewerGEMS, CivilStorm, SewerCAD
Version(s):
CONNECT Edition, V8i
Area:
Modeling
Original Author:
Scott Kampa, Bentley Technical Support Group
Problem
What happens when…
Applies To
Product(s):
StormCAD, SewerGEMS, CivilStorm
Version(s):
V8i, CONNECT Edition
Area:
Modeling
Original Author:
Jesse Dringoli, Bentley Technical Support Group
Problem
Why is the…
Applies To
Product(s):
SewerGEMS, SewerCAD, CivilStorm, StromCAD
Version(s):
V8i, CONNECT Edition
Area:
Output and Reporting
Original Author:
Scott Kampa, Bentley Technical Support Group
Problem…
Product(s):
SewerGEMS, CivilStorm
Version(s):
V8i, CONNECT Edition
Area:
Modeling
Problem
How do I model a gate valve opening and closing based on a logic such as pressure at a pressure transducer (water level in…
Product(s):
SewerCAD, SewerGEMS
Version(s):
CONNECT Edition, V8i
Area:
Calculations
Problem
My SewerGEMS or SewerCAD model takes a very long time to compute. Is there anything I can do to improve calculation performance?
…
Applies To
Product(s):
HAMMER, WaterGEMS, WaterCAD, SewerGEMS, SewerCAD
Version(s):
V8i, CONNECT Edition
Area:
Modeling
Original Author:
Scott Kampa, Bentley Technical Support Group
Problem…
Product(s):
SewerGEMS, CivilStorm
Version(s):
08.11.XX.XX, 10.XX.XX.XX
Area:
Layout and Data Input
Problem Description
When I open my model I get the following error message, "Incompatible dimensions: None != No Units". How…
Applies To
Product(s):
HAMMER
Version(s):
V8i, CONNECT Edition
Area:
Modeling
Original Author:
Jesse Dringoli, Bentley Technical Support Group
Problem
How can a vertical turbine pump, or a…
Product(s):
StormCAD, SewerCAD, SewerGEMS, CivilStorm
Version(s):
V8i, CONNECT Edition
Area:
Output and Reporting
Problem
The calculated slope value shown in the software is slightly off compared to a hand calculation based…
Applies To
Product(s):
CivilStorm, SewerGEMS, PondPack
Version(s):
CONNECT Edition, V8i
Area:
Modeling
Original Author:
Scott Kampa, Bentley Technical Support Group
Problem
Is it possible to…
Product(s):
CivilStorm, SewerGEMS
Version(s):
10.XX.XX.XX
Area:
Calculations
Problem
"Index was outside the bounds of the array" error message when computing the model
Solution
This is a generic error that could occur…
Product(s):
WaterGEMS, Hammer, WaterCAD, SewerGEMS, CivilStorm
Version(s):
CONNECT Edition, V8i
Area:
Layout and Data Input
Problem
When trying to import an EPANET .INP file into WaterGEMS or WaterCAD or an SWMM 5 .INP file…
Applies To
Product(s):
StormCAD, CivilStorm, SewerGEMS
Version(s):
08.11.03.XX and greater
Area:
Calculations, Results and Output
Original Author:
Jesse Dringoli, Bentley Technical Support Group
…
Product(s):
SewerGEMS, SewerCAD, StormCAD, CivilStorm, PondPack
Version(s):
V8i, CONNECT Edition
Area:
Layout and Data Input
Problem
In the MicroStation integrated version, when attempting to create a catchment from a complex…
Product(s):
WaterGEMS, WaterCAD, HAMMER, SewerCAD, SewerGEMS, StormCAD, CivilStorm, PondPack
Version(s):
V8i, CONNECT Edition
Area:
Installation
Problem
When trying to open AutoCAD one of the following error message occurs…
Applies To
Product(s):
WaterGEMS, SewerGEMS, CivilStorm, StormCAD, PondPack, SewerCAD, HAMMER, WaterCAD
Version(s):
CONNECT Edition, V8i
Area:
Installation
Problem
In some cases, you may need to extract…
Applies To
Product(s):
SewerGEMS, CivilStorm
Version(s):
V8i, CONNECT Edition
Area:
Modeling
Original Author:
Mark Pachlhofer, Bentley Technical Support Group
Problem
I'm getting a blocky stepwise…
Product(s):
SewerGEMS, CivilStorm
Version(s):
V8i, CONNECT Edition
Area:
Modeling
Problem
The way in which EPA-SWMM handles pattern vs. time series loads can cause confusion such as:
Pattern loads in SewerGEMS…
Product(s):
WaterGEMS, WaterCAD, HAMMER, SewerGEMS, SewerCAD, StormCAD, CivilStorm
Version(s):
08.11.XX.XX
Area:
Output and Reporting
Problem
Scenario 1
After creating a Project FlexTable you may decide that you want to…
Product(s):
SewerCAD, StormCAD, SewerGEMS, CivilStorm
Version(s):
CONNECT Edition, V8i
Area:
Layout and Data Input
Problem
How can I model an obstruction or clog / blockage in a conduit (pipe) or outlet structure…
Product(s):
WaterGEMS, SewerGEMS, CivilStorm, StormCAD, PondPack, SewerCAD, HAMMER, WaterCAD
Version(s):
08.11.XX.XX, 10.XX.XX.XX
Area:
Output and Reporting
Problem
How do you filter the FlexTables so only active…
Product(s):
WaterGEMS, WaterCAD, StormCAD, SewerCAD, SewerGEMS, CivilStorm, PondPack, HAMMER
Version(s):
10.00.xx.xx, 08.11.xx.xx
Area:
Layout and Data Input
Problem
What file types are supported for background layers for the…