Hi,
In the STAAD section wizard, after creating a built-up box section, I manually change the values of Shear Resisiting Areas ('Ay' 'Az'), width, and thickness of flange and web (TD, TB, D, B) before exporting it as a UPT file.
For such section…
Hello, I have exported the load cases from a STAAD model to a foundation model, and I have begun the design for pile caps. However, I am getting strange values for Dcritical. I have a 48" thick pile cap, and the effective depth calculation reads as follows…
SIG Workshop: STAAD for EMEA - Punching Shear Analysis and Design Using RAM Concept Date/Time: November 26, 2020 11:00 AM CET Presenter: Badreddine Ziane, Senior Manager – Application Engineering, Bentley Systems, Inc. Presenter: Richard Tully, Principal…
Hello Everyone
For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…
Hello Everyone.
I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?
SIG Workshop: Generating Load Combinations in STAAD.Pro CONNECT Edition Date/Time: Thursday, October 15, 2020 at 1:00 PM EDT Presenter: Sabrina Tedeschi,Senior Application Engineer, Bentley Systems, Inc.
Register Now!
This STAAD Special Interest…
Virtual SIG Workshop: STAAD for EMEA - Review of SET Command Specifications to Control Your Solution Date/Time: 24 September 2020 at 11:00 A.M. CEST Presenter: Badreddine Ziane, Senior Manager – Application Engineering, Bentley Systems, Inc.
Register…
SIG Workshop: STAAD - Modeling and Understanding Rigid Diaphragms in STAAD.Pro Date/Time: September 17, 2020 at 1:00 PM EDT Presenter: Sabrina Tedeschi, Senior Application Engineer, Bentley Systems, Inc.
Register Now!
This STAAD Special Interest…
for Seismic design category A structure, 10% of story dead load is required to consider (refer 11.7.2 of ASCE7-05). Does STAAD apply 1% of story dead load as Seismic load or it will calculate as per prescribed procedure based on chapter 12~15 of ASCE7…
Title: SIG VirtualWorkshop: STAAD: Using Tricks of the Trade in STAAD.Pro Editor Date/Time: 20 August 2020 01:00 P.M. EDT Presenter: Karimu Rashad, Senior Application Engineer, Structural, Bentley Systems, Inc.
Register Now
This STAAD Special…
Title: SIG Virtual Workshop: STAAD – From STAAD 3D Models to 2D Design Deliverables Date/Time: June 18, 2020 01:00 P.M. EDT Presenter: Karimu Rashad, Senior Application Engineer, Structural, Bentley Systems, Inc.
Register Now
This STAAD Special…
Cables find applications in many type of structures. In this virtual workshop we shall learn the benefits of non-linear cable analysis and it's applications. In this one hour workshop you will learn the following:
Linear and non-linear cable analysis…
Title: SIG Virtual Workshop: STAAD for EMEA - Geometric Nonlinear Analysis Using STAAD.Pro Advanced Presenter: Badreddine Ziane, Senior Manager – Application Engineering, Bentley Systems, Inc. Date/Time: May 28, 2020 11:00 AM CEST
Register Now
…
It’s easier than ever before to take your project from analysis and design to automated drawing and documentation. Produce the bill of materials and gain instant insight into various design alternatives for the most cost-effective design.
Please join…
SIG Workshop: STAAD – Composite Beam Design to Eurocode Using RAM Beam, Part 2 Host: Badreddine Ziane, Senior Manager, Application Engineering, Bentley Systems, Inc. Presenter: Richard Tully, Advisory Support Engineer, Structural Bentley Systems, Inc…
STAAD Special Interest Group for EMEA: Composite Beam Design to the Eurocode Using RAM Beam Host: Badreddine Ziane, Senior Manager - Application Engineering, Bentley Systems, Inc. Guest Presenter: Richard Tully, Principal Technical Support Engineer, Bentley…
STAAD Special Interest Group: Designing Concrete Walls With STAAD.Pro Host: Sabrina Tedeschi, Senior Content Engineer, Bentley Systems, Inc. Date/Time: 23 January 2020 at 01:00 P.M. EST
Register Now
Attend this STAAD Special Interest Group…
Application
PLAXIS 3D
Version
PLAXIS 3D
Date created
04 May 2017
Date modified
04 May 2017
This video explains how to use the PLAXIS Coupling tool to set up coupled soil-structure interaction analysis between…
Support Policy for STAAD
The Bentley Support Policy has been implemented to help organizations manage their use of Bentley applications, servers, services and license administration. The section below explains how the support policy applies to the…
After analysis i need to modify the geometry of one member. If i need this modification i will lose the cut lines created with results along line tool. I'd like to find a way to not lose the cutting lines after making the modify and relaunching the analysis…