Hi,
In the STAAD section wizard, after creating a built-up box section, I manually change the values of Shear Resisiting Areas ('Ay' 'Az'), width, and thickness of flange and web (TD, TB, D, B) before exporting it as a UPT file.
For such section…
Hello, I have exported the load cases from a STAAD model to a foundation model, and I have begun the design for pile caps. However, I am getting strange values for Dcritical. I have a 48" thick pile cap, and the effective depth calculation reads as follows…
Lately I've been running into issues with my lateral analysis on a large, square steel framed building. The roof is an 1-1/2" metal deck that slopes in one direction and drops 10' over the length of the building, which I've modeled as a semirigid diaphragm…
Hello everyone,
I'm trying to create the structural elements of a boat with the Maxsurf Modeler. Frames, decks and plates are added but I can not add stringers correctly.
I want to add it on a straight line, but it is added on plates.
Below is…
SIG Workshop: STAAD for EMEA - Punching Shear Analysis and Design Using RAM Concept Date/Time: November 26, 2020 11:00 AM CET Presenter: Badreddine Ziane, Senior Manager – Application Engineering, Bentley Systems, Inc. Presenter: Richard Tully, Principal…
Hi everyone,
I would like to inquire what is the significance of mesh intensity in joint meshing. In the Utilities manual, section 3.2.3, the following highlighted statements are made (see screenshot below):
Which lead to these questions:
What…
Hello Everyone
For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…
Hello Everyone.
I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?
Hi I use STAAD Pro Connect V22 Update 3. Here I display a color plot of stresses in a plate between girders. I get Von Mises stresses more than twice as large as the Tresca stresses. How can this be? In theory Tresca shall be equal or larger than Von…
SIG Workshop: Generating Load Combinations in STAAD.Pro CONNECT Edition Date/Time: Thursday, October 15, 2020 at 1:00 PM EDT Presenter: Sabrina Tedeschi,Senior Application Engineer, Bentley Systems, Inc.
Register Now!
This STAAD Special Interest…
SIG Workshop: Software de Análisis Estructural en Español – Análisis P-delta en RAM Elements Date/Time: 30 Septiembre 2020 at 11:00 A.M. CDT Presenter: Andrea Castelo, Ingeniera de aplicaciones, Estructural, Bentley Systems, Inc.
Regístrese ahora
…
Virtual SIG Workshop: STAAD for EMEA - Review of SET Command Specifications to Control Your Solution Date/Time: 24 September 2020 at 11:00 A.M. CEST Presenter: Badreddine Ziane, Senior Manager – Application Engineering, Bentley Systems, Inc.
Register…
SIG Workshop: STAAD - Modeling and Understanding Rigid Diaphragms in STAAD.Pro Date/Time: September 17, 2020 at 1:00 PM EDT Presenter: Sabrina Tedeschi, Senior Application Engineer, Bentley Systems, Inc.
Register Now!
This STAAD Special Interest…
for Seismic design category A structure, 10% of story dead load is required to consider (refer 11.7.2 of ASCE7-05). Does STAAD apply 1% of story dead load as Seismic load or it will calculate as per prescribed procedure based on chapter 12~15 of ASCE7…
Title: SIG VirtualWorkshop: STAAD: Using Tricks of the Trade in STAAD.Pro Editor Date/Time: 20 August 2020 01:00 P.M. EDT Presenter: Karimu Rashad, Senior Application Engineer, Structural, Bentley Systems, Inc.
Register Now
This STAAD Special…
Applies To
Product(s):
AutoPIPE
Version(s):
ALL;
Area:
all
Date Logged & Current Version
July 2020 12.03.00.17
Problem:
Can AutoPIPE create a model from an ISM file?
Solution:
At this time, July 2020, AutoPIPE…
I have modelled one simple structure in STAAD PRO and found that there are two types of displacement value in post processing. NODE and MEMBER.
Which displacement shall i use for comparing with allowable displacement as per BS5950 code.
Title: SIG Virtual Workshop: RAM – Staged Construction Using RAM Structural System Date/Time: June 25, 2020 1:00 P.M. EDT Presenter: Ann Marie Garko-Hill, Senior Manager Application Engineering, Bentley Systems, Inc.
Register Now
This RAM…
Title: SIG Virtual Workshop: STAAD – From STAAD 3D Models to 2D Design Deliverables Date/Time: June 18, 2020 01:00 P.M. EDT Presenter: Karimu Rashad, Senior Application Engineer, Structural, Bentley Systems, Inc.
Register Now
This STAAD Special…
A series of on-demand training videos have been added to the Bentley LEARN Server to learn how to Design Structural Components with the RAM Elements Detailing Modules . The following topics are included in this on-demand training opportunity:
Designing…
Cables find applications in many type of structures. In this virtual workshop we shall learn the benefits of non-linear cable analysis and it's applications. In this one hour workshop you will learn the following:
Linear and non-linear cable analysis…
Title: SIG Virtual Workshop: STAAD for EMEA - Geometric Nonlinear Analysis Using STAAD.Pro Advanced Presenter: Badreddine Ziane, Senior Manager – Application Engineering, Bentley Systems, Inc. Date/Time: May 28, 2020 11:00 AM CEST
Register Now
…