RM Bridge \ Modeler - Circular Elements, Edges, and Construction Lines
In RM Bridge circular elements and radial elements edges, as well as circular construction lines and arched boundaries can be created in Modeler, giving great modeling flexibility.
Initially, users should know that there are new types of construction…
Curved Cross-section Elements
RM Bridge can create curved circular cross-section elements with the use of additional definitions for the Rounding of elements' edges. As shown below, this will apply one constant radius value to one of the sides of the element.
For accuracy or when…
Profile - Annotation of Radius, K or equivalent radius
In File>Design File Settings>Civil Formatting we have the following choices for vertical curve input:
When it comes to annotation, you've got the same choices for the text favorite. Here for vertical change in plan:
Result with parabola:
Result…
Design calculation for crack width for circular members
Can anyone post the detailed calculation of crack width for circular vertical members ?
RAM connection- CHS Column & I beam Weld connection
Hi,
I am new to RAM Connection and wanted to do the moment connection in CHS sections in one of my project. Can I know whether the connection is available now? If so, which version should I install for the same? ( Circular Hollow Section column and…
Removing a Curve From the Complex Element
Hello, i drew lines and placed circular curves at PI points. Once i finished, it turned it into a complex geometry by "Complex by Element". But now i need to remove one of these circular curves and replace it with spiral curve-circular curve-spiral curve…
Using the Polar array tool
Application
PLAXIS 3D
Version
PLAXIS 3D
Date created
06 December 2016
Date modified
06 December 2016
With the polar array tool, you can effortlessly copy objects in circular patterns. Useful to create circular shafts…
Response of a rock mass to circular excavation (non-uniform in-situ stress)
Application
PLAXIS 2D
Version
PLAXIS 2D
Date created
25 February 2016
Date modified
25 February 2016
In the video, we show how to set-up the model discussed in the validation report below. The validation concerns…
Circular tunnel driven in elastic cross anisotropic rocks
Application
PLAXIS 2D
Version
PLAXIS 2D
Date created
26 February 2016
Date modified
26 February 2016
This movie shows how to set-up the model used in the validation document linked below. The validation concerns…
Response of a rock mass to circular excavation (uniform in-situ stress)
Application
PLAXIS 2D
Version
PLAXIS 2D
Date created
25 February 2016
Date modified
25 February 2016
In the video we show how to set-up the model discussed in the validation report below. The validation concerns…
Practical use of the commands runner: Pile field
Application
PLAXIS 3D
Version
PLAXIS 3D
Date created
09 May 2011
Date modified
09 May 2011
The movie shows how to use the commands runner for more efficient modelling. The generation of a circular pile field was…
Interface around circular tunnel may take material from wrong side
Application
PLAXIS 2D
Issue status
✔ Solved
First Affected Version
PLAXIS 2D AE.00
Found in Version
PLAXIS 2D AE.00
Fixed and Released in Version
PLAXIS 2D 2015.00
Issue #
22252
Date created
11…
Circular tunnel with inside interface cannot be meshed
Application
PLAXIS 2D
Issue status
✔ Solved
First Affected Version
PLAXIS 2D AE.00
Found in Version
PLAXIS 2D AE.00
Fixed and Released in Version
PLAXIS 2D 2015.00
Issue #
21347
Date created
03…
Bearing capacity of a circular footing
Application
PLAXIS 2D PLAXIS 3D
Version
PLAXIS 2D PLAXIS 3D
Date created
12 November 2012
Date modified
12 November 2012
This document describes an example that has been used to verify the ultimate limit state capabilities…
Modeling Circular Inlet Grates in StormCAD
I am trying to model some Neenah Foundry inlet grates in sag that are circular for a senior design capstone project. I am trying to use a ditch inlet type since there are not any curbs surrounding these inlets however the grate types provided do represent…
How to Change the graphics of Pipe Union from Hexagonal to Circular
Applies To
Product(s):
OpenPlant Modeler
Version(s):
08.11.11.XXX
Environment:
Windows 7/8.1/10 (64 bit)
Area:
Component
Subarea:
Component and Graphics
Original Author:
Kunal Kiran, Bentley Product Advantage…
How can I place Smartline with ARC??
I tried to make "PLACE SMARTLINE" with arc. ...But It's difficult.
I need your help to solve thid problem.
I wrote thid code using "IPrimitiveCommandEvents" to draw the line string but,, It is difficult to make arc with line.
This…