File > Import > List Input File | Generate Report ... Joint selection > Table > Joint List
Hi fellow colleagues,
Regarding Bentley SACS Precede CONNECT Edition V16, I would like to understand more on the function of the Joint List which is seen in the Report Selection in the joint tab for relevant report type.
I want to generate the…
06l. Guidance for modelling Bell and Spigot type joint
A spigot joint is a type of pipe fitting that is inserted into another pipe fitting, the joint was caulked with hemp rope impregnated with pine resin and sealed in place with molten lead. So, we have to get this molten lead holding capacity to check will…
How To Manage Rubber Lined Gasket in OpenPlant Modeler
Applies To
Product(s):
OpenPlant Modeler
Version(s):
CONNECT Edition
Environment:
Windows 10 (64 bit)
Area:
Customization
Subarea:
Original Author:
Fer Mykiel Gonzales, Bentley Technical Support Group…
Add Joint to Bridge Deck in Open Bridge
I'm creating a 15 span prestressed girder bridge in OpenBridge Modeler. I need to add a neoprene strip seal joint every 3 spans or so. Can I modify the continuous deck object to add these components? Alternatively, splitting the deck object into multiple…
Concrete Joint Stiffness
Hi all,
In order to model contact between two concrete blocks we are using an specific interface with a Mohr-Coulomb soil model. For concrete volumes we are using concrete model.
Our point of view is that joint stiffness (E' for interface) should…
"Maximum Number of Joint Names Exceeded"
Problem:
I have quite a large structural model made of both beams and plates. When refining some of the plates, I got the following message "Maximum number of joint names exceeded". What should I do?
Solution:
In Precede settings, set the Joint…
MOSES | Tubular Joint Fatigue
Hello,
The following presented the example of the MOSES Output for Tubular Joint Fatigue. Based on this, the upper and lower CDR is for Brace and Chord respectively. It is understood that, the Joint *J1359 - Node *J2031 is belong to the Brace Element…
MOSES| Structural Post Processing
Hello,
I am referring to Moses Reference Manual Rev 11.03.00
For JOINT POST -CODE " {CODE option he need not be re-issued. EDITION defines the edition of RP2A which will be used checked for the check. If it is OLD, then the first supplement of the…
How to Create a Custom Joint in OpenPlant Modeler Connect
Applies To
Product(s):
OpenPlant Modeler
Version(s):
CONNECT Edition 10.08.00.51 (Update 8)
Environment:
Windows 8.1/10 (64-bit)
Area:
Schema
Subarea:
Joint
Original Author:
Aishwarya Kulkarni, Bentley…
13. Composite Structures - Join Split
Composite structures loads considering the erection sequence in the simulation with partially completed elements has a complex structural system that changes in time and requires a non-linear stress distribution as shown in the picture below.
This…
Permeability in interfaces
Application
PLAXIS 2D PLAXIS 3D
Version
PLAXIS 2D 2017 PLAXIS 3D 2017
Date created
03 July 2017
Date modified
03 July 2017
PLAXIS 2D 2017 and PLAXIS 3D 2017 have has several new features. One of them is permeability…
Using permeability in interfaces
Application
PLAXIS 2D PLAXIS 3D
Version
PLAXIS 2D PLAXIS 3D
Date created
18 April 2017
Date modified
18 April 2017
This movie demonstrates how to apply the cross and parallel permeability options for interfaces…
Joint Check - "No beams fixed to column flange"
Hi,
I am trying to model the frame from the RAM Structural System Tutorial. Inside the RAM Frame module, I performed the Joint Check which outputted all joints to be "OK" However, when I check the joints through "View/Update Joints" It shows a red signal…
01. AutoPIPE's Flexible Joint Dialog Explained
Applies To
Product(s):
AutoPIPE,
Version(s):
All
Area:
Modeling
Original Author:
Bentley Technical Support Group
Nov 2014, AutoPIPE V8i 09.06.01.10
Problem:
AutoPIPE's Flexible…
.i - "Flexible Joints" - Example Modeling Approaches in AutoPIPE
Comments, Questions, and Answers about the Example modeling approaches for "Flexible Joints"
Overview:
Please see the following AutoPIPE help section: Help > Contents> Contents Tab> Modeling Approaches> Modeling Approaches> Flexible Joints
There…
ACI 318 SMF Joint Capacity Check Strong Column Weak Beam
Applies To
Product:
RAM Concrete
First Affected Version:
Found in Version:
15.03.00
Fixed in Version:
15.06.00
Area:
Design
Issue #:
624602
Problem Description
In the…
Wafer Joint on Components with Different Facing and Rating Shows Error While Placement
Applies To
Product(s):
OpenPlant Modeler
Version(s):
08.11.09.XXX (SS5) | 08.11.11.XXX (SS6)
Environment:
Windows 7/8.1/10 (64 bit)
Area:
Component
Subarea:
Properties
Original Author:
Harpreet Singh,…
RE: OPM SS6 - monolithic joint
Hello Tuan,
One easier way would be to create a custom component as it has a fixed dimension for each size. I believe, joints creation has no role here as the two end comes with a butt weld end and you can easily show a parametric component similar…
RE: OpenPlant Modeler, Gaskets
Thanks Shaun for the response,
Very good to see, that it has been resolved!
Keep checking all articles and do let us know if we assist you further on OpenPlant Issues.
Cheers!
-Regards | Rahul Kumar
To Fix Joint Connection Error While Modeling Component
Applies To
Product(s):
OpenPlant Modeler
Version(s):
08.11.11.87
Environment:
Windows 7/8/10 (64 bit)
Area:
Component
Subarea:
Error Message
Original Author: …
Redefining a chord for a joint
Q: MOSES did not choose the correct chord for a joint, how do I redefine it? REV 7.00
A: MOSES finds the largest "thru member" and proclaims it the chord. The only control the user has over this is to alter your model so the largest thru member is the…
Bottom clearance measurement point
Q: Is the bottom clearance (or the maximum submergence) measured from the lowest joint or does MOSES really compute the lowest point? REV 6.01
A: MOSES really computes the lowest point (based on the data he is given); i.e. the size of any beam is used…
To Fix Welds on Olets in OpenPlant Modeler
Applies To
Product(s):
OpenPlant Modeler
Version(s):
08.11.09.581
Environment:
Windows 7 (64 bit) | Windows 8
Area:
Component
Subarea:
Graphics - Olets-Welds-Placement
…
Invalid Joint Error while Validating Joint for Custom Components
Applies To
Product(s):
OpenPlant Modeler
Version(s):
08.11.09.564 & above
Environment:
Windows 7 (64 bit)
Area:
Component
Subarea:
Custom Component - Connectivity Checker
…
Can't Assign CCB_SP to some CBB Joints
Applies To
Product:
Ram Connection
First Affected Version:
11.00.00.164
Found in Version:
11.00.00.177
Fixed in Version:
11.00.01.208
Environment:
All
Area:
General
Issue…