AccuDraw Coordinate System Rotation Auto Changes to Auxiliary
Product:
MicroStation
Version:
CONNECT, 2023
Environment:
N/A
Area:
Drawing Aids
Subarea:
AccuDraw
Problem
The Coordinate System Rotation setting in the AccuDraw Settings keeps reverting to…
Rotation of a single mesh element (triangle) in Plaxis 3D
Dear Ladies and Gentlemen!
Is there a way to get the rotation of triangles of a mesh (single mesh element)?
I have dummy plates with low stiffness to evaluate the deformation of shallow foundations (slab) from different buildings above a NAT-Tunnel…
Effect of raft thickness on rotation in piled raft foundations
Hello,
I have modeled a piled raft foundation using Plaxis 3D and increased the thickness of the raft (plate element) to investigate its effect on the foundation behavior. However, the results showed that increasing the thickness of the raft caused…
Rotation Angle from feature property (PBS?)
Hi all. Me again
I've seen few posts about same issue but it seems that deficiency is still here (e.g. link link link ).
What I want is to create PBS or something similar that consider value in ANGLE property of the feature and apply rotation angle…
Cut/Fill Lines Upside-down
So I have ramps on my project. As everyone knows, ramp stationing runs with traffic. Because of this my cut and fill lines in the corridor are upside-down. Is there a way to just change the display for linework created in a corridor.
OBD - Array with Rotation applied
Hi all,
I'm doing the trackwork by using the Open Building Designer.
Does anyone know how to array the element (or cell) with certain degree of rotation vertically?
I array the sleeper along the alignment line, however from the straight to curve…
Need to Understand 2D Cell Rotation Angle When Cell is Mirrored About the Y-axis
Hi All,
I have a program that needs to unrotate a 2D cell to 0 deg/no reflection which has been placed at any rotation angle and/or mirrored about the X- and/or Y-axis.
Specifically, the problem I'm having is when the cell has been mirrored about…
How To Enable or Disable Rotation for OFF-PAGE CONNECTOR in OpenPlant PID Connect Edition.
Applies To
Product(s):
OpenPlant P&ID
Version(s):
Connect Edition
Environment:
Windows 10 (64-bit)
Area:
Page Connectors Orientation
Subarea:
N/A
Original Author:
Harshavardhan K,Bentley Product Advantage…
Why are my DXF files not shown (properly) in OpenRoads Designer?
I have a 100+ .dxf (Drawing eXchange Format, from Autodesk) files that are traffic signs.
When I place them as cell in OpenRoads Designer, the visual does not appear at all or is only shown partly/in some views.
I have tried to change the .dxf file…
View not rotating as expected
Product:
MicroStation
Version:
XM, V8i, CONNECT
Environment:
N\A
Area:
View
Subarea:
View Navigation
Problem
The view is not rotating as expected When applying a rotation (Top, Right, etc.…
View dependent Element Labels - Sewergems for Microstation
I am wondering if there is a feature request for the element labels in Sewergems for Microstation to be view dependent?
I notice the labels say they're "View Dependent" in the Microstation Properties window, but they aren't actually and do not rotate…
Visual 3D Cube
Problem Description:
I am using a 3D Connexion mouse and work in both Microstation and Inventor. The Cube in Inventor is very handy. Does Microstation have something similar?
Solution:
Work around for now would be to create a cell using construction…
Component Rotation
HI, Recently I insert a component but I cannot rotate it. I check the property. It show the orientation is top (color grey). I want to rotate it to vertical. It only can rotate it on top surface. How to correct it?
Thanks
RE: [Connect update 4] Problem with TextNode Rotation
Unknown said: Here is attached dgn file
Your text node is view independent . It has no rotation, and is always displayed in the plane of the view. Most elements don't give the user that option, so you will encounter it mostly with text and text nodes…
07. What units and factors are applicable in order to convert rotations from an AutoPIPE modal analysis report into actual rotations values?
Applies To
Product(s):
AutoPIPE
Version(s):
ALL;
Environment:
N/A
Area:
Original Author:
Bentley Technical Support Group
Date Logged & Current Version
Jan. 2017 10.01.00.09
Problem:
What units…
RE: OPM - Pipe Insulation Saddle adjust angle
Hello Ray,
Believe this could be logged as an Enhancement. We will Confirm the number soon.
-Regards | Rahul Kumar
RE: [Connect VBA] Problem with rotation matrix3d
Hi,
I have tried to understand what exactly happens, but a couple of variables are not defined within the code snipped, so it´s a lot of assuming. So I tried to reduce the problem and created my own code example using your approach trying to simulate…
"Center of Rotation" with the RARM command
Q: Where is the "Center of Rotation" with the RARM command? REV 7.00
A: There is not "center of rotation"! The ship is rotated and equilibrium is found. The vertical position is a result of the equilibrium. In the results, a draft, roll, and trim are…
Heave motions from the frequency domain
Q: Are the heave motions from the frequency domain coupled with rotations? REV 5.05
A: Yes.
08. Why is there no moment column on the Results Grids - support tab in AutoPIPE?
Applies To
Product(s):
AutoPIPE
Version(s):
2004, XM, V8i, CONNECT;
Environment:
N/A
Area:
Subarea:
Original Author:
Bentley Technical Support Group
Date Logged…
Component Rotation - Point Not Found
When trying to rotate a component of the model about a point that was just created, AutoPipe gives the warning that the point cannot be found and does not allow to proceed with the operation. This has happens again and again even with program reboots…
RE: View rotation problem - coordinates and actual view don't match
Here are some suggestions
1. You can use the left and right or Up and down arrow keys in the keyboard which would give better control.
2. Setting the center of rotation to an existing node may be helpful in some cases. You can do that using the last…
Structure Rotation and Member Orientation Problems
Hi there,
Really hope someone out there has managed to crack this one..
In my STAAD Pro model I am required to rotate the whole structure around a specific member/line. This I can quite easily accomplish with the Rotate command. No problems there…
Re: Symbolization in Map Manager distorts point data
Hello!
Thank you to report that unexpected beahvior on this Forum.
Lot of factors can explain this behavior. We need to ask you more precisions, beginning with:
Do you have any rotation in the view (both models)?
Do you assign any Coordinate…
Re: text orientation with CreateTextNodeElement1
Gianluca:
Private Sub IPrimitiveCommandEvents_Dynamics(point As Point3d, ByVal oView As View, ByVal drawMode As MsdDrawingMode)
Dim rotation As Matrix3d
rotation = Matrix3dIdentity
Set oTextElement = CreateTextNodeElement1 (Nothing, point,…