• Custom Supports Changing Location

    CT
    CT
    OpenPlant Modeler V8i (SS6) 08.11.11.304 Hello, We have been placing custom supports based on the link below: https://communities.bentley.com/products/plant/w/plant_design_and_engineering__wiki/21404/to-add-custom-cell-for-supports-in-openplant…
    • Answered
    • over 2 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • To Hide supports in OpenPlant Isometrics Manager

    Kestutis Mitkus
    Kestutis Mitkus
    Applies To Product(s): OpenPlant Isometrics Manager Version(s): 08.11.11.87 Environment: Windows 7 (64 bit) & others Area: Settings/Attributes Subarea: Original Author…
    • over 4 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Wiki
  • RE: Support on bend transition

    Rahul Kumar
    Rahul Kumar
    Hello Richard, Thanks for Logging a Service Request for this. Based on SR # 7000497956 , we have filed an Enhancement # 438858 to it. This will further gets evaluated by the product management team & development team. Submitting it for your information…
    • over 7 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • RE: Support on bend transition

    Rahul Kumar
    Rahul Kumar
    Thanks Richard, I also checked on same. I believe you have a valid point here. Normally on fittings placing support is not recommended. But in case of Bends with certain clamp length may be a case where supports are required. We are checking the possibilities…
    • over 7 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • RE: Support on bend transition

    Rahul Kumar
    Rahul Kumar
    Hi Richard, I tried placing it on Bend with tangent length but no luck so far. What version you are using here? -Regards | Rahul Kumar
    • over 7 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • To Display Support Orientation in OpenPlant Isometrics Manager

    Kestutis Mitkus
    Kestutis Mitkus
    Applies To Product(s): OpenPlant Isometrics Manager Version(s): 08.11.09.440 & above Environment: Windows 7 (64 bit) Area: Settings/Attributes Subarea: Original Author…
    • over 4 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Wiki
  • RE: Saddles in OPM

    Rahul Kumar
    Rahul Kumar
    Hello Grant, Can you provide some more input here? This will help us to assist you further. Also Please check below wiki article on similar issue. wiki - http://communities.bentley.com/products/plant/design___engineering/w/plant_design_and_engineering__wiki…
    • over 7 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • RE: Saddles in OPM

    Rahul Kumar
    Rahul Kumar
    Hello Grant, Thanks for your Query. Do you need saddle dimensions to be controlled through spec? Please confirm. -Regards | Rahul Kumar
    • over 7 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • How to Round Off Values After Decimal For Support Co-ordinates

    Kestutis Mitkus
    Kestutis Mitkus
    Applies To Product(s): OpenPlant Isometrics Manager Version(s): 08.11.09.404 & above Environment: Windows 7 64 bit & Others Area: Settings/Attributes Subarea: Original…
    • over 4 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Wiki
  • Grouping of Supports Based on Common Tag Name

    Kestutis Mitkus
    Kestutis Mitkus
    Applies To Product(s): OpenPlant Isometrics Manager Version(s): 08.11.09.XXX (SS5) | 08.11.11.XXX (SS6) Environment: Windows 7/8.1/10 (64 bit) Area: Settings/Attributes Subarea: Configuring the BOM and Reports…
    • over 4 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Wiki
  • RE: Open Plant Support Engineering and AutoPIPE

    Rahul Kumar
    Rahul Kumar
    Hello Jonatan, Based on above query on importing correct PXF file to AutoPipe, we have created a Service Request, SR # 7000454039 and filed a Defect # 360702 for this. This will further gets evaluated by development team and Product Management Team…
    • over 7 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum