• 04. Would friction be considered during any movement of of piping supported by an incline support with Ultimate Force Gap setting enabled?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Modeling Date Logged & Current Version June 2022 12.08.01.010 Problem: If an inclined support had a friction coefficient with Ultimate Force Gap enabled…
    • over 1 year ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 03. Are results are the same / different when running a Non-Linear or Dynamic analysis with Ultimate Force Gap option enabled or disabled in AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Modeling Date Logged & Current Version June 2022 12.08.01.010 Problem: When performing an analysis with an incline support configured as shown below…
    • over 1 year ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 02. Are results are the same / different when running a Linear analysis with Ultimate Force Gap option enabled or disabled in AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Modeling Date Logged & Current Version June 2022 12.08.01.010 Problem: Are the results the same or different when running a linear analysis with Ultimate…
    • over 1 year ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 05. Non-Linear Analysis - Pipe / Support Friction Force - Load Case GrP1T1E1

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE, Version(s): ALL Area: Analysis Original Author: Bentley Technical Support Group Problem: The support at this location (ex. AB03), is a V-stop support, with…
    • over 2 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • V-Stop vs Line Stop in Vertical Pipe?

    Dipesh Khadka
    Dipesh Khadka
    I want to know what is the difference between using a line stop and a v-stop in a vertical pipe? If a v-stop is used with gaps 0mm, does it mean same as line stop with gap 0mm? In which condition of vertical pipe should we use line stop or v-stop…
    • Answered
    • over 5 years ago
    • AutoPIPE
    • AutoPIPE Forum
  • 04. Non-Linear Analysis - Pipe / Support Friction Force - Load Case GrP1T1

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE, Version(s): ALL Environment: N/A Area: Analysis Original Author: Bentley Technical Support Group Problem: Simply, the support at this location,…
    • over 2 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 02. Non-Linear Guide vs Inclined Supports Explained in AutoPIPE

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Description…
    • over 7 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • Support Reaction

    MOJO_JOJO
    MOJO_JOJO
    Can someone please tell me how to use the results that are contained in the Support Reaction print-out? I gather that, for a model to be structurally correct, the values there should all be zero; none of the springs are supposed to be carrying any forces…
    • over 13 years ago
    • RAM | STAAD | ADINA
    • RAM | STAAD Forum
  • Error in RAM Elements Version 11.0.1 (Build 15)

    sbouvia
    sbouvia
    While trying to design a model which is all steel members, the following error pops up; SteelCollection.dll not registered. I have included a snipping of the error window. Any help would be great. Regards, Scott
    • over 12 years ago
    • RAM | STAAD | ADINA
    • RAM | STAAD Forum